American Petroleum Institute, 2018. — 394 p. This specification identifies requirements and gives recommendations for the performance, dimensional and functional interchangeability, design, materials, testing, inspection, welding, marking, handling, storing, shipment, and purchasing of wellhead and tree equipment for use in the petroleum and natural gas industries.
1th. Ed. — API, June 2018. — 258 p. Status: Active. This standard covers the minimum dry gas sealing system requirements in association with axial, centrifugal, and rotary screw compressors and expanders for use in the petroleum, chemical, and gas industry services as described in API 617 and API 619. API 692 does not apply to other types of shaft seals such as clearance seals,...
11th Ed. — API, October 2022. — 83 p. This inspection code covers the in-service inspection, repair, alteration, and rerating activities for pressure vessels and the pressure- relieving devices protecting these vessels. This inspection code applies to all refining and chemical process vessels that have been placed in service unless specifically excluded per This includes: a....
Американский институт нефти. 124 с. Дата вступления в силу: 1 декабря 2008 г. Перевод на русский язык. В данной части стандарта приводятся требования для замковых резьбовых соединений, используемых в нефтяной и газовой промышленности, включая требования к геометрическим параметрам резьбы и резьбовым калибрам, условия применения калибров, а также методы проверки резьбовых...
Восьмое издание, сентябрь 2014 г., список исправлений 1, август 2016 г, 388 страниц, Американский нефтяной институт. API 617 состоит из перечисленных ниже частей, объединенных общей темой «осевые и центробежные компрессоры и компрессоры-расширители специального назначения, работающие с газом или технологическим воздухом». Общие требования. Центробежные и осевые компрессоры, не...
5th edition. — API, 2007. — 193 p. This standard is based on the accumulated knowledge and experience of manufacturers and users of reciprocating compressors. The objective of this publication is to provide a purchase specification to facilitate the procurement and manufacture of reciprocating compressors for use in petroleum, chemical, and gas industry services. The primary...
Восьмое издание, 1 июля 2005 г. ISO 11960:2004, Нефтяная и газовая промышленности – Стальные трубы для использования в качестве обсадных и насосно-компрессорных труб для скважин. Дата введения: 1 января 2006г. Область применения. Соответствие. Ссылки на нормативы. Единицы измерения. Ссылки на нормативы. Термины, определения, символы и сокращения Термины и определения. Символы и...
3rd edition, august 2001, American Petroleum Institute, 37 pages. This specification was formulated to provide for the availability of safe, dimensionally and functionally interchangeable high pressure fiberglass line pipe with a Specification 15HR Standard Pressure Rating from 500 lbf/in.2 to 5000 lbf/in.2, inclusive, in 250 lbf/in.2 increments. This specification is limited...
Recommended API, 2013, American petroleum institute, 34 p. This RP applies to all parts of a pipeline or pipeline facility including line pipe, pump station piping, terminal piping, compressor station piping, metering station piping, delivery station piping, regulator station piping, appurtenances connected to line pipe, appurtenances connected to facility piping, fabricated...
American Petroleum Institute, 2022. — 239 p. The 2022 edition lists API standards, recommended practices, and other technical documents to help the natural gas and oil industry operate safely, efficiently, and responsibly supply energy to billions of people around the world. API standards and recommended practices are developed by leading industry subject-matter experts to...
API Publishing Services, 2021. — 1478 p. The methods and procedures in this Standard are intended to supplement and augment the requirements of API 510, API 570, API 653, and other post-construction codes that reference 𝐹𝐹𝐹𝐹𝐹𝐹 evaluations such as NB-23.
Технические условия. — Двадцать первое издание, ноябрь 2018 года. Дата вступления в силу программы монограммы API: ноябрь 2019 г. Список исправлений 1, апрель 2019 г. Дата издания июль 2020 г. — США, American Petroleum Institute. — 418 с. В настоящих технических условиях указаны требования и даны рекомендации для технической характеристики, размерной и функциональной...
5-е издание, апрель 2008 г. (с перечнем опечаток, май 2008 г.) — 233 с. Предисловие API. Предисловие. Вводная часть. Часть 1: Общие требования. Часть 2: Масляные системы специального назначения. Часть 3: Масляные системы общего назначения. Часть 4: Автономные системы поддержки газовых уплотнений. (ZIP-архив из 4-х PDF-фалов, содержащих четыре части стандарта).
3-е издание, июнь 2004 г. — Дата вступления в действие: декабрь 2004 г. — Американский нефтяной институт, 2004. Настоящий Американский национальный стандарт устанавливает требования, предъявляемые к эксплуатационным характеристикам, конструкции, материалам, испытаниям и контролю, сварке, маркировке,погрузочно-разгрузочным работам, хранению и отгрузке бурового оборудования,...
12th Edition. — American Petroleum Institute (API), 2021. — 233 p. This standard specifies requirements for centrifugal pumps, including pumps running in reverse as hydraulic power recovery turbines (HPRTs), for use in petroleum, petrochemical, and gas industry process services. This standard is applicable to overhung pumps, between-bearings pumps, and vertically suspended...
American Petroleum Institute (API), Fourth Edition, July 2020. — 116 p. — Recommended Practice 575. This document provides useful information and recommended practices for the maintenance and inspection of atmospheric and low-pressure storage tanks. While these maintenance and inspection guidelines may apply to other types of tanks, these practices are intended primarily for...
7th Edition. — American Petroleum Institute, 2020. — 237 p. This standard is applicable to pressure-relieving and vapor depressuring systems. Although intended for use primarily in oil refineries, it is also applicable to petrochemical facilities, gas plants, liquefied natural gas (LNG) facilities, and oil and gas production facilities. The information provided is designed to...
American Petroleum Institute, 2020. — 183 p. This recommended practice (RP) provides guidance to the API authorized inspector on welding inspection as encountered with fabrication and repair of refinery and chemical plant equipment and piping, pipelines, and other related industries. This RP includes descriptions of common welding processes, welding procedures, welder...
5th edition. — API Publishing Services, 2010. — 150 p. This part of ISO 10440 is based on API 619, 4th edition, December 2004, with the intent that the 5th edition of API 619 will be identical to this part of ISO 10440. Users of this part of ISO 10440 should be aware that further or differing requirements may be needed for individual applications. This part of ISO 10440 is not...
5th edition. — API Publishing Services, 2008. — 238 p. This part of ISO 10438 specifies general requirements for lubrication systems, oil-type shaft-sealing systems, dry gas face-type shaft-sealing systems and control-oil systems for general- or special-purpose applications. General purpose applications are limited to lubrication systems. These systems can serve equipment such...
3rd edition. — API Publishing Services, 2017. — 170 p. This standard specifies requirements and provides guidance for the selection, design, specification, operation, and maintenance of flares and related combustion and mechanical components used in pressure relieving and vapor-depressurizing systems for petroleum, petrochemical, and natural gas industries. While this standard...
API Publishing Services, 2008. — 62 p. This part of ISO 15136 has been developed by users/purchasers and suppliers/manufacturers of progressing cavity pump surface-drive systems and is intended for use in the petroleum and natural gas industry worldwide. ISO 15136-2 provides requirements and information to both parties in the selection, manufacturing, testing, and using...
API Publishing Services, 2010. — 122 p. This part of ISO 15136 has been developed by users/purchasers and suppliers/manufacturers of progressing cavity pumps and is intended for use in the petroleum and natural gas industry worldwide. This part of ISO 15136 provides requirements and information to both parties in the selection, manufacturing, testing, and using progressing...
Third Edition. — American Petroleum Institute (API). — March 2020. — 376 p. This recommended practice discusses damage mechanisms applicable to oil refineries; however, much of the information herein can also be applied to petrochemical and other industrial applications, as the user deems appropriate. It is up to the user to determine the applicability and appropriateness of...
13th edition. — API, March 2020. — 514 p. This standard establishes minimum requirements for material, design, fabrication, erection, and inspection for vertical, cylindrical, aboveground, closed- and open-top, welded storage tanks in various sizes and capacities for internal pressures approximating atmospheric pressure (internal pressures not exceeding the weight of the roof...
5th edition. — API, May 2020. — 189 p. — Add 1 (April 2018) and Add 2 (May 2020). This standard covers steel storage tanks built to API 650 and its predecesor API 12C. It provides minimum requeriments for maintaining the integrity of such tanks after they have been placed in service and addresses inspection, repair, alteration, relocation, and reconstruction.
American Petroleum Institute. — Dallas, 1988. API Recommended Practice. Validity of Calculations. Discussion. Design Procedure. Apendix: Discussion of Nondimensional Parameters. Includes Errata.
This specification identifies requirements and gives recommendations for the performance, dimensional and functional interchangeability, design, materials, testing, inspection, welding, marking, handling, storing, shipment, and purchasing of wellhead and tree equipment for use in the petroleum and natural gas industries. This specification does not apply to field use or field...
First Edition. American Petroleum Institute, 1970. This Standard has been prepared as a guide for design, installation, and operationof turbine meter system in liquid hydrocarbon service. Primary emphasis is placed on the turbine meter and its accessories, but many of the concepts and innovations described are adaptable to other devices concerned with the volumetric measurement...
API RECOMMENDED PRACTICE 752. CMA MANAGER'S GUIDE, FIRST EDITION, MAY 1995. This publication is intended to assist management in identifying process plant buildings of concern, understanding the associated hazards, and managing the risk. The hazards that normally can affect the occupants of buildings include fire. explosion. and toxic releases. This publication provides a...
1992. American Petroleum Institute. Third Edition, July 1991. Reaffirmed, May 1996. This standard describes tests to determine the seat tightness of metal- and soft-seated pressure relief valves. Valves of conventional, bellows. and pilot-operated designs are covered. Acceptable leakage rates are defined. Tests with air, steam, and water are described. This standard requires the...
Американский нефтяной институт. Третья редакция, ноябрь 2012 г. Исправление опечаток, июнь 2014 г. Настоящий стандарт охватывает минимальные требования к возвратно-поступательным насосам для объектов нефтяной, химической и газовой промышленности. 75 страниц.
8th edition. — American Petroleum Institute, 2007. — 52 p. This International Standard specifies requirements and gives recommendations for the mechanical design, material selection, fabrication, inspection, testing and preparation for shipment of shell-and-tube heat exchangers for the petroleum, petrochemical and natural gas industries. This International Standard is...
Перевод на русский язык. — ЗАО «Технорматив», 2008. Pipe threads, general purpose (inch). Данный американский государственный стандарт распространяется на размеры и калибры трубных резьб для применений общего назначения. Переработка и переиздание ANSI B2.1-1968. Повторное утверждение 1992.Подтверждено в 2006 г Предисловие. Введение. Область действия. Обозначения резьбы....
Девятое издание, июнь 2013 г. Дата введения: 1 июня 2014. Настоящая спецификация посвящена системам менеджмента качества и предназначена для использования предприятиями нефтяной и газовой отраслей промышленности, производящими продукцию или осуществляющих ее техническое обслуживание в соответствии с техническими условиями. В ней сформулированы основные требования, которым должны...
Fifth Edition. — American Petroleum Institute, 1998. — 52 p. This standard covers the normal and emergency vapor venting requirements for aboveground liquid petroleum or petroleum products storage tanks and aboveground and underground refrigerated storage tanks designed for operation at pressures from vacuum through 15 pounds per square inch gauge (1.034 bar gauge). Discussed...
1974. American Petroleum Institute.—74 p. This recommended practice is intended as an authoritative reference for all individuals and organizations concerned with safe design? installation? and operation of electrical facilities for petroleum processing plants. This standard provides a basis for those specifications that industry and engineering contractors develop for inclusion...
API is a leader in the development of petroleum and petrochemical equipment and operating standards covering topics that range from drill bits to environmental protection. These embrace proven, sound engineering and operating practices and safe, interchangeable equipment and materials. Many have been incorporated into state and federal regulations and adopted by ISO for worldwide...
API is pleased to present its 2018 publications programs and services catalog. The 2018 edition lists API standards, recommended practices, equipment specifications, other technical documents, and reports and studies to help the oil and natural gas industry safely, efficiently, and responsibly supply energy to billions of people around the world. For upstream, API publications...
Nordic APIs AB, 2015. — 120 p. — ASIN B011ACJ368. Целевая аудитория: опытные разработчики. На сегодняшний день почти каждое приложение имеет свой API, которое предназначено или для сторонних разработчиков, или для внутреннего фронтенда, или для того и другого вместе. Данное руководство поможет вам контролировать жизненный цикл вашего API и микросервисов, освещая современные...
Издательство: American Petroleum Institute (API). Язык: Русский. Число страниц: 116. Число изменений: 2 (на английском языке) на 28 страницах. Опубликовано: 01.12.2017. Настоящая спецификация охватывает размеры, допуски и требования к маркировке для резьб API и калибров, с помощью которых осуществляется контроль критериев приемки резьбы. Калибры резьбовых элементов, приборы и...
This document specifies requirements for the performance, dimensional and functional interchangeability, design, materials, testing, inspection, welding, marking, handling, storing, shipment, purchasing, repair, and remanufacture of wellhead and tree equipment for use in the petroleum and natural gas industries. This document does not apply to field use, field testing, or field...
API recommended practice 684 (second edition, august 2005; reaffirmed, november 2010) API Standard Paragraphs Rotordynamic Tutorial: Lateral Critical Speeds, Unbalance Response, Stability, Train Torsionals, and Rotor Balancing
API (Американский нефтяной институт). 2002. Первая редакция. 131 с. Настоящая РП (рекомендованная практика) содержит информацию, предназначенную для предварительного использования инженерами, имеющими практические знания в сфере электрических систем и технологических операций. Некоторая часть этой информации может быть полезной для опытного персонала, занимающегося техническим...
2002 American Petroleum Institute. Первая редакция, февраль 1996 года. Этот стандарт охватывает минимальные требования к жидкостным кольцевым вакуумным насосам и компрессорам, предназначенным для эксплуатации в нефтяной, химической и газовой промышленности. Они включают как требования к конструкции вакуумных насосов и компрессоров, так и к конструкции системы.
2002 American Petroleum Institute. Третье издание, сентябрь 1996 года. Этот стандарт основан на накопленном знании и опыте производителей и пользователей компактных, цельноприводных центробежных воздушных компрессоров. Цель этого стандарта – обеспечить технические требования при покупке, чтобы содействовать производству и продвижению этих компрессоров для использования в...
THIRD EDITION, FEBRUARY 2018 28p. The purpose of this recommended practice (RP) is to provide guidelines for an owner/user to develop and implement a material verification program (MVP) as part of an asset integrity program. The MVP uses positive material identification and other methods to verify that the nominal composition of an asset, an asset component, or weldment within...
Перевод оригинального американского стандарта "Системы снижения давления и аварийного сброса давления" на русский язык. ШЕСТОЕ ИЗДАНИЕ, ЯНВАРЬ 2014 - 258 с. Стандарт действующий. Этот стандарт применим для систем сброса и снижения давления пара. Хотя он предназначен для использования в первую очередь для нефтеперерабатывающих заводов, он также применим для нефтехимических...
American Petroleum Institute (API) Forty-Sixth Edition, April 2018. 205p. Effective date: November 1, 2018 API SPECIFICATION 5L, 46TH EDITION We are pleased to announce the publication of the 46th edition of Specification 5L, Line Pipe. This new edition provides technical updates that have reached consensus within API’s Subcommittee on Tubular Goods and will now give industry...
2nd Edition. — American Petroleum Institute (API). — April 2013. — 90 p. This standard serves as an umbrella document to be used with and complement companion standards. NACE SP0102, In-line Inspection of Pipelines and ASNT ILI-PQ, In-line Inspection Personnel Qualification and Certification all have been developed enabling service providers and pipeline operators to provide...
American Petroleum Instltute (API), September 2002. 64p. The purpose of the study was to provide technical background, based on industry experience and consensus practice, for controlling corrosion in hydroprocess reactor effluent systems.
Четвертое издание. — 100 с. Этот стандарт основан на накопленном знании и опыте производителей и пользователей газовых турбин для нефтяной, химической и газовой промышленности. Цель этого документа – обеспечить технические требования при покупке, чтобы содействовать производству и продвижению газовых турбин, предназначенных для использования в нефтяной, химической и газовой...
American Petroleum Instltute (API) Third Edition, February 2016. 94p. This recommended practice (RP) is intended to provide guidance on eveloping a Risk-Based Inspection (RBI) program for fixed equipment and piping in the hydrocarbon and chemical process industries.
American Petroleum Instltute (API) Third Edition, April 2016. 632p. This recommended practice, API RP 581, Risk-Based Inspection Methodology, provides quantitative procedures to establish an inspection program using risk-based methods for pressurized fixed equipment including pressure vessel, piping, tankage, pressure relief devices (PRDs), and heat exchanger tube bundles.
American Petroleum Institute (API). — June 2008. — 57 p. — First Edition. Use of 9Cr-1Mo-V (Grade 91) Steel in the Oil Refining Industry. This report is only applicable to the 9Cr-1Mo-V alloy steel, Grade 91.
American Petroleum Institute (API), February 2015, 58p, Third Edition. Techanical Report 938-C, Use of Duplex Stainless Steels in the Oil Refining Industry. This report covers many of the “lean”, “standard”, “super”, and “hyper” grades of duplex stainless steels (DSSs) most commonly used within refineries.
American Petroleum Institute (API). — First Edition, May 2009. — 50 p. This recommended practice (RP) is applicable to hydrocarbon process streams containing sulfur compounds, with and without the presence of hydrogen, which operate at temperatures above approximately 450 °F (230 °C) up to about 1000 °F (540 °C).
American Petroleum Institute (API). — Seventh Edition, July 2013. — 160 p. This Standard gives requirements and recommendations for the design, materials, fabrication, inspection, testing and preparation for shipment of air-cooled heat exchangers for use in the petroleum, petrochemical and natural gas industries.
American Petroleum Institute (API). Seventh Edition, August 2008. — 56 p. This recommended practice summarizes the results of experimental tests and actual data acquired from operating plants to establish practical operating limits for carbon and low alloy steels in hydrogen service at elevated temperatures and pressures. The effects on the resistance of steels to hydrogen at...
1994 г. Американский нефтяной институт-53 стр. Данный стандарт охватывает минимальные требования по роторным насосам, которые эксплуатируются в нефтяной, химической и газовой отраслях промышленности. Для получения информации по поршневым насосам смотрите API Стандарт 674, по дозировочным насосам – Стандарт 675.
Стандарт API 670. Четвертое издание. Декабрь 2000. Американский нефтяной институт 1220 L Street, Northwest Washington, D.C. 20005-100 стр. Данный стандарт включает минимальные требования к системам защиты оборудования, производящим измерения радиальной вибрации вала, вибрации корпуса, осевого положения вала, частоты вращения вала, падения поршневого штока, фазовой референции,...
February 1990.American Petroleum Institute-23 p. This recommended practice is intended to assist in the management of process hazards. It is intended to help prevent the occurrence of, or minimize the consequences of, catastrophic releases of toxic or explosive materials. This recommended practice addresses the management of process hazards in design, construction, start-up,...
Copyright 1981. American Perroleum lnstitute. This checklist is intended to assist the Contractor and Owner in defining their separate responsibilities in the execution of work assignments as the plant or various areas. systems, and facilities of the plant are being completed. It is also intended to facilitate the transfer of responsibility from the Contractor to the Owner for the...
American Petroleum Institute, 1996. — 78 p. This standard covers the minimum requirements for liquid ring vacuum pump and compressor systems for service in the petroleum, chemical, and gas industries. This includes both vacuum pump and compressor design and system design. The design of the system is critical to the successful operation of the liquid ring vacuum pump or...
1994. American Petroleum Institute. This standard covers the minimum requirements for controlled volume positive displacement pumps for use in service in the petroleum, chemical, and gas industries. Both packed-plunger and diaphragm types are included. Diaphragm pumps that use direct mechanical actuation are excluded. See API Sumdard 674 for reciprocating pumps and Standard 676...
2003. Copyright American Petroleum Institute-100 p. This standard covers the minimum requirements for a machinery protection system measuring radial shaft vibration, casing vibration, shaft axial position, shaft rotational speed, piston rod drop, phase reference, overspeed, and critical machinery temperatures (such as bearing metal and motor windings). It covers requirements for...
2006. Copyright American Petroleum Institute -126 p. API Publishing Services, 1220 L Street, N.W., Washington, D.C. 20005. This International Standard gives requirements and recommendations for the design, materials, fabrication, inspection, testing and preparation for shipment of air-cooled heat exchangers for use in the petroleum and natural gas industries. This International...
American Petroleum Instltute (API) First Edition, May 2002. 60p. The purpose of this document is to provide users with the basic elements for developing and implementing a risk-based inspection (RBI) program. The methodology is presented in a step-by-step manner to the maximum extent practicable. Although the risk management principles and concepts that RBI is built on are...
This Recommended Practice is under the joint jurisdiction of the API Exploration and Production (E&P) Department Committee on Production Equipment Standards, the API Manufacturing Distribution and Marketing (MDM) Department, Committee on Refinery Equipment, and the Pipeline Operations Technical Committee. It is based upon a level of knowledge gained through experience and through...
Sixth edition, April 2011. The proper installation of an UST system can contribute toward ensuring that the maximum utilization of the various components and equipment comprising an UST system are achieved at the lowest total cost of ownership. This will help prevent, as well as reduce, the frequency and magnitude of releases that may result from equipment failure or malfunction....
Выпуск – Май 2004 (6-й выпуск) Язык – Русский Страниц – 22 Область применения – Данный стандарт распространяется на конструкцию, материалы, строительные размеры, классы по давлению и температуре, а также на требования по контролю, инспекциям и испытаниям для арматуры, изготовленной из серого и ковкого чугуна, бронзы, стали, сплавов на основе никеля и особых сплавов, которая...
American Petroleum Institute (API). Fourth Edition, February 1996. Reaffirmed 10/2008. 16 p. These procedures describe a recommended method for conducting drop-weight tear tests to measure the fracture ap- pearance or fracture ductility of tine pipe as referenced in API Specification 5L, Specification fur Line Pipe. Metric conversions of US customary units are shown in...
1320 стр.
American Petroleum Institute, The American Society of Mechanical Engineers, JUNE, 2016
The methods and procedures in this Standard are intended to supplement and augment the requirements in API 510, API 570, API 653, and other post construction codes that reference FFS evaluations such as NB-23.
The assessment procedures in this Standard can be used for...
American Petroleum Institute (API). THIRD EDITION, NOVEMBER 2009. 78p. This recommended practice describes the inspection and repair practices for automatic pressure-relieving devices commonly used in the oil and petrochemical industries. As a guide to the inspection and repair of these devices in the user's plant, it is intended to ensure their proper performance. This...
122 стр. c Приложением
Annex A (informative) External Inspection Checklist for Process Piping
FOURTH EDITION, NOVEMBER 2016
This recommended practice (RP) supplements API 570 by providing piping inspectors with information that
can improve skill and increase basic knowledge of inspection practices. This RP describes inspection
practices for piping, tubing, valves (other than...
154 стр. c Приложениями
Annex A (informative) Exchangers
Annex B (informative) Towers
Annex C (informative) Sample Record Forms
FOURTH EDITION, DECEMBER 2016
This recommended practice (RP) covers the inspection of pressure vessels. It includes a description of the various types of pressure vessels (including pressure vessels with a design pressure below 15 psig) and the...
American Petroleum Institute (API). THIRD EDITION, OCTOBER 2013. 120p. This recommended practice covers the inspection practices for fired boilers and process heaters (furnaces) used in petroleum refineries and petrochemical plants. The practices described in this document are focused to improve equipment reliability and plant safety by describing the operating variables which...
Дата введения: 1 апреля 2011 г. Данный международный стандарт, который был технически пересмотрен, основан на API Spec 6А, девятнадцатого издание, июль 2004 г., c дополнениями и исправлениями, и API Spec 6AV1, первое издание, февраль 1996 года с исправлениями, с той целью, чтобы двадцатый выпуск API Spec 6A был идентичен данному международному стандарту. В данном Международном...
American Petroleum Institute (API). First Edition. July 2009. 42 p. This standard provides environmentally sound practices for domestic onshore oil and gas production operations. It is intended to be applicable to contractors as well as operators. Facilities within the scope of this document include all production facilities, including produced water handling facilities. Offshore...
American Petroleum Institute (API). Thirteenth Edition, October 2011. Errata, April 2012. 34p. This recommended practice covers typical wire rope applications for the oil and gas industry. Typical practices in the application of wire rope to oil field service are indicated in Table 1, which shows the sizes and constructions commonly used. Because of the variety of equipment...
Publisher: API Publish Date: 2016 Pages: 36 Language: English Format: PDF Document Scope Scope. This standard covers design, materials, face-to-face dimensions, pressure-temperature ratings, and examination, inspection and test requirements for gray iron, ductile iron, bronze, steel, nickel-based alloy, or special alloy butterfly valves.
Publisher: API Publish Date: 2016 Pages: 144 Language: English Format: PDF Document Scope This recommended practice (RP) is applicable to any pipeline system used to transport hazardous liquid or natural gas, including those defined in U.S. Title 49 Code of Federal Regulations (CFR) Parts 195 and 192. This RP is specifically designed to provide the operator with a description...
Издание 4. 2016г
Язык: Английский
Страниц: 88
Формат: PDF
Обзор:
Стандарт API 570 регламентирует процедуры контроля, ремонта, модернизации и реклассификации металлических трубопроводных систем, подвергавшихся эксплуатации.
Стандарт API 570 разработан для нефтеперерабатывающей и нефтехимической отраслей, но мо-жет использоваться, если он практически применим, в отношении...
American Petroleum Institute (API). Draft #5, July 3, 2010. 62 p. This publication is intended to provide recommended practices for the use of gas-lift automation to enhance the functionality and profitability of gas-lift operations for the production of oil and gas. The scope of this document addresses the following topics: Production automation definition. Overview of...
American Petroleum Institute (API). Draft #12, January 15, 2011. 175 p. This API Recommended Practice covers the application of dynamic simulation for gas-lift wells and systems. Dynamic simulation is an important tool to assist in the design, operation, surveillance, troubleshooting, and diagnosis of gas-lift processes. Most gas-lift design and diagnosis programs have used...
Publisher: API Publish Date: 2015 Pages: 84 Language: English Format: PDF Document Scope The scope of this technical report is to provide design guidelines for oil and gas subsea equipment utilized in highpressure high-temperature (HPHT) environments (refer to 3.1.16). For the purpose of the technical report, HPHT environments are intended to be one or a combination of the...
American Petroleum Institute (API). First Edition. June 2008. 182 p. This API document presents guidelines and recommended practices for the design and operation of intermittent, chamber, and plunger gas-lift systems. This document also contains three annexes. Annex A contains mathematical derivations and models of some of the most pertinent intermittent gas-lift calculations....
American Petroleum Institute (API). Fourt Edition. ANSI Approved September 2011. Revised September 2012. 28 p. The procedures established in this document govern the development of standards published by the American Petroleum Institute (API). All API standards development activities shall be conducted in accordance with these Procedures. API committees responsible for...
American Petroleum Institute (API). First Edition. September 1981. Reaffirmed October 2002, Reaffirmed March 2002. 42 p. This pubrication defines the various terms (be they words or symbols) employed in the caicuiation of metered petroleum quantities. Where two or more terms are customarily employed in the oil industry for die same thing. this publication selects what should...
American Petroleum Institute (API). American Society for Testing and Materials (ASTM). Third Edition, October 1995. 30 p. This standard presents procedures for manually obtaining samples of petroleum and petroleum products of a liquid, semi-liquid, or solid state whose vapor pressure at ambient conditions is below 101.32 kilopascals (14.7 pounds per square inch absolute)....
American Petroleum Institute (API). Second Edition, Ballot Draft July 2012. 6 p. This standard identifies equations of state (EOS) suitable for use in custody transfer measurement of pure ethylene (>99 %) in the gaseous, liquid, and super critical phases. Given flowing temperature and pressure, each equation of state identified in this document is capable of calculating density,...
American Petroleum Institute (API). First Edition. December 1994. 28 p. This standard describes the following: (a) the procedures for manually gauging the liquid level of petroleum and petroleum products inn on-pressure fixed-roof, floating-roof tanks and marine tank vessels, (b) procedures for manually gauging the level of free water which may befo und with the petroleum or...
American Petroleum Institute (API). First Edition. Draft Dated 04.23.2014. 67 p. The scope of this technical report is for the design evaluation of oil and gas subsea equipment utilized in high-pressure high-temperature (HPHT) environments. For the purpose of the technical report, HPHT environments are intended to be one or a combination of the following well conditions: 1) The...
American Petroleum Institute (API) First Edition, November 1997. Reaffirmed 11/2002. 144 p. The purpose of this recommended practice is to provides guidelines for classifying locations Class I, Zone 0, Zone 1, and Zone 2 locations at petroleum facilities for the selection and installation of electrical equipment.
American Petroleum Institute (API). Draft #6, October 3, 2008. Version: April 30, 2016. 134 p. The purpose of this document is to provide recommended practices for the design, operation, optimization, and troubleshooting of dual gas-lift wells. Compared to single completions, dual completions have a higher initial cost, have more operating problems, are more difficult and...
American Petroleum Institute (API). First Edition, August 2009. Errata 1: October 2009. 228 p. This part of ISO 10407 specifies the required inspection for each level of inspection (Tables B.1 through B.15) and procedures for the inspection and testing of used drill stem elements. For the purpose of this part of ISO 10407, drill stem elements include drill pipe body, tool joints,...
Publisher: API Publish Date: 2014 Pages: 162 Language: English Format: PDF Document Scope The purpose of this recommended practice is to provide guidelines for classifying locations Class I, Division 1 and Class I, Division 2 at petroleum facilities for the selection and installation of electrical equipment. Basic definitions given in the 2011 Edition of NFPA 70, National...
American Petroleum Institute (API). First Edition. November 2007. 24 p. This publication is designed to aid companies in initiating the development of a safety and environmental management system (SEMS). The intent is to identify a series of tools to assist in the development and implementation, or improvement, of the system. The design of each company’s system will be unique and...
American Petroleum Instltute (API). Third Edition, Draft. June 12, 2008. 138 p. This document discusses the system components and presents a summary of recommended practices for recognizing and dealing with many of the problems that may cause upsets and/or inefficient operations in continuous gas-lift. The checklist below may be used as a quick reference guide for spotting and...
Американский институт нефти. 16 издание. Август.1998. С дополнением от ноября 2003. Дата вступления в силу: 1 мая 2004 г. 207 стр. Перевод на русский язык. Данные рекомендации распространяются не только на выбор элементов буровой колонны, но и на контроль угла наклона скважины, выбор буровых жидкостей, скорость бурения, весовых нагрузок и других эксплуатационных параметров.
American Petroleum Instltute (API) Second Edition. April 2011. 372 p. This recommended practice provides general guidance as to the most likely damage mechanisms affecting common alloys used in the refining and petrochemical industry and is intended to introduce the concepts of service-induced deterioration and failure modes. These guidelines provide information that can be...
American Petroleum Institute (API). First Edition. December 2014. 18 p. The purpose of this document is to provide guidance on operating and maintenance practices for the storage and handling of petroleum coke (petcoke). In particular, guidance is provided on the management of airborne particulate matter emissions and water runoff from petcoke storage facilities. A variety of...
American Petroleum Institute (API). Eighth Edition. May 2014, 24 p. This document provides guidelines and establishes requirements for inspection, maintenance, repair, and remanufacture of items of hoisting equipment manufactured according to API 8A, API 8C, or ISO 13535 used in drilling and production operations, in order to maintain the serviceability of this equipment.
American Petroleum Instltute (API). Third Edition, Draft. 12.09.2008 – Ballot 2. 175p. The purpose of this recommended practice (RP) is to provide guidelines for classifying locations Class I, Division 1 and Class I, Division 2 at petroleum facilities for the selection and installation of electrical equipment. Basic definitions given in the 2008 Edition of NFPA 70, National...
Publisher: API Publish Date: 2015 Pages: 78 Language: English Format: PDF Document Scope This recommended practice (RP) sets criteria for the design, construction, testing, operation, and maintenance of offshore steel pipelines utilized in the production, production support, or transportation of hydrocarbons; that is, the movement by pipeline of hydrocarbon liquids, gases, and...
Американский институт нефти. 22 издание. Введено 01.06.2002. С поправкой от 01.03.2005. 71 стр. Перевод на русский язык. Этот стандарт определяет требования и дает рекомендации по конструкции, изготовлению, испытанию и документации шаровых кранов, обратных клапанов, задвижек и пробковых кранов для применения в трубопроводных системах, соответствующих требованиям ISO 13623 для...
Publisher: API Publish Date: 2014 Pages: 20 Language: English Format: PDF Document Scope This standard specifies the requirements and acceptance criteria (100 ppmv) for fugitive emission type testing of rising and rising-rotating stem valves equipped with packing previously tested in accordance with API 622. Packing shall be suitable for use at service temperatures –29 °C to...
Publisher: API Publish Date: 2016 Pages: 340 Language: English Format: PDF Document Scope This standard specifies requirements and gives recommendations for the design, materials, fabrication, inspection, testing, preparation for shipment, and erection of fired heaters, air preheaters (APHs), fans, and burners for general refinery service. This standard does not apply to the...
Training course for API 570. Kuwait Petroleum Corporation. Год издания - 2006 Язык - английский Страниц - 431 Формат - PDF Preparatory course for API 570 exam.
Training course for API 653 Год издания - 2005 Язык - английский Страниц - 203 Формат - PDF Preparatory course for API 653 exam. Tank Inspection Code: Inspection, repair, alteration, and reconstruction of steel aboveground storage tanks used in the petrochemical industry. Harvard Technology Middle East
Publisher: API Publish Date: 2016 Pages: 302 Language: English Format: PDF Document Scope This standard establishes minimum requirements for material, design, fabrication, erection, and inspection for vertical, cylindrical, aboveground, closed- and open-top, welded storage tanks in various sizes and capacities for internal pressures approximating atmospheric pressure (internal...
Publisher: API Publish Date: 2009 Pages: 124 Language: English Format: PDF Size: 2 218 Kb Document Scope This International Standard provides procedures for the laboratory testing of both drilling fluid materials and drilling fluid physical, chemical and performance properties. It is applicable to both water-based and oil-based drilling fluids, as well as the base or make-up...
Publisher: API Publish Date: 2001 ( Reaffirmed 2015 ) Pages: 48 Language: English Format: PDF Size: 339 Kb Document Scope This recommended practice provides external fusion bonded epoxy coating of line pipe for use in transportation pipelines. The Recommended Practice is limited to the application of external coatings on pipe prior to installation. There may exist differences...
Publisher: API Publish Date: 2011 Pages: 274 Language: English Format: PDF Size: 2 291 Kb Document Scope ( API Spec 17D is identical to ISO 13628 Part.4 ) This part of ISO 13628 provides specifications for subsea wellheads, mudline wellheads, drill-through mudline wellheads and both vertical and horizontal subsea trees. It specifies the associated tooling necessary to handle,...
Publisher: API Publish Date: 2002 Pages: 36 Language: English Format: PDF Size: 320 Kb Document Scope This recommended practice provides guidelines for safely conducting welding, cutting or other hot work activities in refineries, gas plants, petrochemical plants and other facilities in the petroleum and petrochemical industries. It includes specific guidance to evaluate...
Publisher: API Publish Date: 2007 Pages: 58 Language: English Format: PDF Size: 849 Kb Document Scope 1.1 PURPOSE This Recommended Practice (RP) focuses on the design and implementation of displays used for the display, monitoring, and control of information on pipeline Supervisory Control and Data Acquisition Systems (SCADA). The primary purpose is to document industry...
Publisher: API Publish Date: 2013 Pages: 34 Language: English Format: PDF Size: 497 Kb Document Scope This RP applies to all parts of a pipeline or pipeline facility including line pipe, pump station piping, terminal piping, compressor station piping, metering station piping, delivery station piping, regulator station piping, appurtenances connected to line pipe, appurtenances...
Publisher: API Publish Date: 2009 (Errata 2011) Pages: 78 Language: English Format: PDF Size: 858 Kb Document Scope 1.1 This recommended practice (RP) sets criteria for the design, construction, testing, operation, and maintenance of offshore steel pipelines utilized in the production, production support, or transportation of hydrocarbons; that is, the movement by pipeline of...
Publisher: API Publish Date: 2003 Pages: 34 Language: English Format: PDF Size: 930 Kb Document Scope 1 This RP covers required and recommended features of the following aspects of bottom loading and vapor recovery: a. The configuration and operation of 4-in. (101.6 mm) adapters for bottom loading. b. Tank vehicles equipped for bottom loading or vapor recovery. c. Secondary...
Publisher: API Publish Date: 2013 Pages: 18 Language: English Format: PDF Size: 184 Kb Document Scope This recommended practice (RP) may supplement the API equipment specifications for carbon and low alloy steel large cross section and critical components. The recommend practice described herein suggests the requirements for batch-type bath quench and water spray quench-type...
Publisher: API Publish Date: 2015 Pages: 124 Language: English Format: PDF PRODUCT NO. G16C02 Size: 2030 kB Scope This specification establishes the minimum requirements for the design and manufacture of the following types of new equipment: a) articulated choke and kill lines; b) choke and kill manifold buffer chamber; c) choke and kill manifold assembly; d) drilling choke...
Publisher: API Publish Date: 2015 PRODUCT NO. C938C03 Pages: 70 Language: English Format: PDF Size: 1363 kB Scope This report covers many of the lean, standard, super, and hyper grades of duplex stainless steels (DSSs) most commonly used within refineries. The definitions of these terms have not been firmly established by the industry, and vary between literature references and...
Publisher: API
Publish Date: 2014
Pages: 60
Language: English
Format: PDF
Size: 623 kB
Scope
This standard provides installation quality control procedures for monolithic refractory linings and may be used to supplement owner specifications. Materials, equipment, and personnel are qualified by the methods described, and applied refractory quality is closely monitored,...
Publisher: API
Publish Date: 2015
Pages: 120
Language: English
Format: PDF
Size: 3042 kB
Scope
This specification covers seamless, centrifugal cast, and welded alloy line pipe with improved corrosion resistant properties. The purpose of this specification is to provide standards for pipe with improved corrosion resistance suitable for use in conveying gas, water, and...
Publisher: API
Publish Date: 2015
Pages: 74
Language: English
Format: PDF
Size: 932 kB
Scope
This recommended practice (RP) presents recommendations for designing, installing, and testing a process safety
system for subsea applications. The basic concepts of subsea safety systems are discussed and protection methods
and requirements of the system are outlined.
For...
Publisher: API Publish Date: 2014 Pages: 386 Language: English Format: PDF PRODUCT NO. C61708 Scope Covers the minimum requirements for axial compressors, single-shaft and integrally geared process centrifugal compressors, and expander-compressors for use in the petroleum, chemical, and gas industries services that handle air or gas. Part 1— General Requirements, contains...
Publisher: API Publish Date: 2015 Pages: 280 Language: English PRODUCT NO. C53007 Format: PDF Document Scope This standard specifies the requirements and gives recommendations for the procedures and design criteria used for calculating the required wall thickness of new tubes and associated component fittings for fired heaters for the petroleum, petrochemical, and natural gas...
API, 2015. — 66 p. Product Number: C60209 This international standard specifies the requirements for a series of compact steel gate, globe and check valves for petroleum and natural gas industry applications.It is applicable to valves of: nominal pipe sizes NPS 1/4, NPS 3/8, NPS 1/2, NPS 3/4, NPS 1, NPS 1 1/4, NPS 1 1/2, NPS 2, NPS 2 1/2, NPS 3, and NPS 4; corresponding to...
Publisher: API
Publish Date: 2006
Pages: 104
Language: English
Product Number: C67703
Covers the minimum requirements for general-purpose, enclosed, single,
and multistage gear units incorporating parallel shaft helical and right angle
spiral bevel gears for the petroleum, chemical, and gas industries. Gears
manufactured according to this standard shall be limited to the...
This standard covers the minimum requirements for general-purpose steam turbines. These requirements include basic design, materials, related lubrication systems, controls, auxiliary equipment and accessories.
American Petroleum Institute (API), January, 2015. p42. Full Description This standard specifies the requirements for a heavy-duty series of bolted bonnet steel gate valves for petroleum refinery and related applications where corrosion, erosion, and other service conditions would indicate a need for full port openings, heavy wall sections, and large stem diameters. This...
American Petroleum Institute (API) Spec 14A 12th Ed, January 2015. 150p Effective Date: January 15, 2016 API Product No. G14A12 This specification provides the requirements for subsurface safety valves (SSSVs), and the secondary tools as defined herein necessary to operate the features included within them, including all components that establish tolerances and/or clearances...
American Petroleum Institute (API) STANDARD 660 NINTH EDITION, March 2015. 72P. Shell-and-Tube Heat Exchangers This standard specifies requirements and gives recommendations for the mechanical design, material selection, fabrication, inspection, testing, and preparation for shipment of shell-and-tube heat exchangers for the petroleum, petrochemical, and natural gas industries....
1 Scope Note: No provision of this recommended practice shall be cause for rejection of casing or tubing provided the threads are in accordance with the requirements of the latest edition of API Standard 5B. 1.1 The statements on corrosion of casing and tubing as given herein were developed with the cooperation of the Technical Practices Committee on Corrosion of Oil and Gas Well...
This standard is applicable to pressure-relieving and vapor depressuring systems. Although intended for use primarily in oil refineries, it is also applicable to petrochemical facilities, gas plants, liquefied natural gas (LNG) facilities, and oil and gas production facilities. The information provided is designed to aid in the selection of the system that is most appropriate for...
This document defines the quality management system requirements for service supply organizations for the petroleum, and natural gas industries. It is intended to apply to the execution of services during exploration, development and production in the oil and gas industry. This includes activities involved in upstream oil and gas well construction, intervention, production, and...
American Petroleum Institute (API) THIRD EDITION, OCTOBER 2011. 100p. Many facilities in the refining and petrochemical processing industries employ contractor personnel for a wide range of activities, from administrative support to equipment repair, maintenance, and construction. Contractor activities that involve work in or around process equipment can have an increased...
American Petroleum Institute (API) FOURTH EDITION, JANUARY 2013. 62p. Effective date: AUGUST 1, 2013
This specification states requirements and gives recommendations for suitable steel structures for drilling and well servicing operations in the petroleum industry, provides a uniform method of rating the structures, and provides two Product Specification Levels (PSLs).
This...
This recommended practice (RP) provides recommendations for evaluation of a manufacturer's valve construction and quality management system for the purpose of determining a manufacturer's capability to provide new valves manufactured in accordance with the applicable standards listed in Section 2. Qualification of valves under this RP is "manufacturing facility specific" and...
This standard covers the minimum requirements for special purpose form-wound squirrel cage induction motors 375 kW (500 hp) and larger for use in petroleum, chemical, and other industry applications. This standard can also be used for induction generators by substituting "generator" for "motor" where applicable.
This Standard is applicable to flares used in pressure relieving and vapor-depressuring systems used in general refinery and petrochemical services. The information provided is intended to aid in the design and selection of a flare system that is most appropriate for the risks and circumstances. Although this Standard is primarily intended for new flares and facilities, it may be...
This standard covers methods of installation for pressure-relief devices (PRDs) for equipment that has a maximum allowable working pressure (MAWP) of 15 psig (1.03 barg or 103 kPAg) or greater.
Pressure-relief valves (PRVs) or rupture disks (RDs) may be used independently or in combination with each other to provide the required protection against excessive pressure...
This specification covers material, design, fabrication, and testing requirements for vertical, cylindrical, aboveground, closed and open top, bolted steel storage tanks in various standard sizes and capacities for internal pressures approximately atmospheric, not to exceed those listed in Section 4.1. This specification is designed to provide the oil production industry with...
The purpose of this document is to provide owners/users with practices for developing, implementing, sustaining, and enhancing an investigation program for pressure equipment integrity (PEI) incidents. This recommended practice (RP) describes characteristics of how an effective investigation could be structured so organizations can learn from PEI incidents. This RP is not intended...
The purpose of this recommended practice (RP) is to explain the importance of integrity operating windows (IOW's) for process safety management and to guide users in how to establish and implement an IOW program for refining and petrochemical process facilities for the express purpose of avoiding unexpected equipment degradation that could lead to loss of containment. It is not...
This standard specifies the minimum requirements for sealless centrifugal pumps for use in petroleum, heavy duty petrochemical and gas industry services. This standard is applicable to single stage overhung pumps of two classifications, Magnetic Drive Pumps (MDP) and Canned Motor Pumps (CMP).
This API standard specifies the requirements for a heavy-duty series of bolted bonnet steel globe valves for petroleum refinery and related applications where corrosion, erosion and other service conditions would indicate a need for heavy wall sections and large stem diameters.
Provides guidance on the selection of common types of valves used by the petroleum refining, chemical, petrochemical and associated industries. These include gate, ball, plug, butterfly, check, and globe valves covered by the API and ASME Standards. Modulating control valves and pressure relief valves are outside the scope of this RP.
This International Standard specifies requirements and gives recommendations for the design, materials, fabrication, inspection, testing and preparation for shipment of steam turbines for special-purpose applications. It also covers the related lube-oil systems, instrumentation, control systems and auxiliary equipment. It is not applicable to general-purpose steam turbines, which...
API's new edition of Specification Q1, Specification for Quality Management System Requirements for Manufacturing Organizations for the Petroleum and Natural Gas Industry, efficiently meets industry demands for an improved quality management system among manufacturing organizations. The new edition of Spec Q1 contains 85+ new requirements and 5 new sections. Additional advantages...
This standard has been developed from the accumulated knowledge and experience of qualified engineers of the oil, petroleum, petrochemical, chemical, and general bulk liquid storage industry. Engineering studies of a particular tank can indicate that the appropriate venting capacity for the tank is not the venting capacity estimated in accordance with this standard. The many...
Provides a basis for establishing the ratings of main load carrying components of certain hoisting equipment used in drilling and production operations to include the maximum load and bearing load. This specificatin provides the manufacturer with material and process controls for adequately assuring that manufactured units will meet the established design load ratings.
This document provides guidelines and establishes requirements for inspection, maintenance, repair, and remanufacture of items of hoisting equipment manufactured according to API 8A, API 8C, or ISO 13535 used in drilling and production operations, in order to maintain the serviceability of this equipment.
The purpose of this guidance document is to identify and describe practices currently used in the oil and natural gas industry to minimize surface environmental impacts-potential impacts on surface water, soils, wildlife, other surface ecosystems and nearby communities-associated with hydraulic fracturing operations. While this document focuses primarily on issues associated with...
This standard applies to the sizing and selection of pressure-relief devices used in refineries, chemical facilities, and related industries for equipment that has a maximum allowable working pressure (MAWP) of 15 psig (103 kPag) or greater. The pressure-relief devices covered in this standard are intended to protect unfired pressure vessels and related equipment against...
This recommended practice establishes general principles for the safe operation and maintenance of offshore pedestal-mounted revolving cranes on fixed or floating offshore platforms, offshore support vessels, jackup drilling rigs, semi-submersible drilling rigs and other types of mobile offshore drilling units (MODUs). This document also provides requirements and recommendations...
This specification covers material, design, fabrication, and testing requirements for fiberglass reinforced plastic (FRP) tanks. Only shop-fabricated, vertical, cylindrical tanks are covered. Tanks covered by this specification are intended for above ground and atmospheric pressure service at various sizes and capacities ranging from 90 to 1500 barrels. Unsupported cone bottom...
This specification covers minimum requirements for material, design, fabrication, and testing of vertical and horizontal emulsion treaters. Emulsion treating is normally conducted on crude oil immediately after it is separated from its associated gas in a vessel referred to as a treater or sometimes as a heater treater. High gas-oil ratio wells or those produced by gas lift may...
This specification covers minimum requirements for the design, fabrication, and shop testing of oilfield indirect type fired heaters that are used in the production of oil, gas and associated fluid. The heaters are located at some point on the producing flowline between the wellhead and pipeline. Heater components covered by this specification include the pressurized coils, the...
This specification covers minimum requirements for the design, fabrication, and plant testing of oil and gas separators and oil-gas-water separators that are used in the production of oil and gas, and are located at some point on the producing flow line between the wellhead and pipeline. Separators covered by this specification may be vertical, spherical, or single or double...
This specification covers material, design, fabrication, and testing requirements for shop-fabricated vertical, cylindrical, aboveground, closed top, welded steel storage tanks with internal pressures approximately atmospheric at various sizes and capacities ranging from 90 to 750 barrels. Tanks covered by this specification have been designed using established engineering...
This specification covers material, design, fabrication, and testing requirements for vertical, cylindrical, aboveground, closed top, welded steel storage tanks with internal pressures approximately atmospheric at various sizes and capacities ranging from 500 to 10000 barrels. Tanks covered by this specification have been designed using established engineering calculations to...
API 12B FIFTEENTH EDITION, OCTOBER 2009, 46 PAGES This specification covers material, design, fabrication, and testing requirements for vertical, cylindrical, aboveground, closed and open top, bolted steel storage tanks in various standard sizes and capacities for internal pressures approximately atmospheric, not to exceed those listed in Section 4.1
American Petroleum Institute (API). First Edition, July 2013. 54p. This recommended practice covers the basic requirements and their associated references needed to effectively and safely perform inspection activities during construction of new onshore pipelines. Use of this document will provide the basis for what construction inspectors need to know and where to find detailed...
American Petroleum Institute (API) Fourth Edition, September 2014. 46p. The purpose of this recommended practice is to present procedures and practices for achieving effective corrosion control on aboveground storage tank bottoms through the use of cathodic protection. It contains provisions for the application of cathodic protection to existing and new storage tanks. Corrosion...
This recommended practice (RP) covers the design,
maintenance, inspection, and mitigation practices to
address external corrosion under insulation (CUI) and
corrosion under fireproofing (CUF). The document
discusses the external corrosion of carbon and low alloy
steels under insulation and fireproofing and the external
chloride stress corrosion cracking (ECSCC) of austenitic...
API Std 682, MAY 2014, 4th Ed. 268 P.
This standard specifies requirements and gives recommendations for sealing systems for centrifugal and rotary pumps used in the petroleum, natural gas, and chemical industries. See A.1.1 and A
.1.2. It is the responsibility of the purchaser or seal vendor to ensure that the selected seal and auxiliaries are suitable for the intended...
API STANDARD 674, THIRD EDITION, DECEMBER 2010, 108 P. ERRATA, MAY 2014 Full Description Covers the minimum requirements for reciprocating positive displacement pumps for use in petroleum, chemical, and gas industry services. Both direct-acting and power-frame types are included. Scope Normative References Terms and Definitions General Statutory Requirements Basic Design...
API Standard 673, THIRD EDITION, DECEMBER 2014, 124 P
This standard covers the minimum requirements for centrifugal fans for use in petroleum, chemical, and gas industry services. Fan static pressure rise is limited to differential usually not exceeding 130 in. (330 cm) of water equivalent air pressure from a single impeller or each impeller in a two stage fan. This standard...
API STANDARD 663 Hairpin-type Heat Exchangers, MAY 2014, 54 P, 1st Ed. Description This standard specifies requirements and gives recommendations for the mechanical design, materials selection, fabrication, inspection, testing and preparation for shipment of hairpin heat exchangers for use in the petroleum, petrochemical and natural gas industries. Hairpin heat exchangers...
API STANDARD 625, Tank Systems for Refrigerated Liquefied Gas Storage, August 2010, 74p, 1st Ed. ADDENDUM 1, JULY 2013, ADDENDUM 2, NOVEMBER 2014 This standard covers low pressure, above ground, vertical, and cylindrical tank systems storing liquefied gases requiring refrigeration. This standard provides general requirements on responsibilities, selection of storage concept,...
American Petroleum Institute (API) 12th Edition, October 2013. 290p
ADDENDUM 1, NOVEMBER 2014
The API Downstream Segment has prepared this standard to cover large, field-assembled storage tanks of the type described in 1.2 that contain petroleum intermediates (gases or vapors) and finished products, as well as other liquid products commonly handled and stored by the various...
Published: September 1, 2009
Number of Pages: 20
API 598 covers inspection, examination, supplementary examinations, and pressure test requirements for resilient-seated, nonmetallic-seated (e.g. ceramic), and metal-to-metal-seated valves of the gate, globe, plug, ball, check, and butterfly types.
American Petroleum Institute (API). Fourth Edition, June 1995. 98 p. This standard covers the minimum requirements for special purpose steam turbines for petroleum, chemical, and gas industry services. These requirements include basic design, materials, and related lube-oil systems, controls, and auxiliary equipment.
American Petroleum Institute (API). Tenth Edition 20xx, Effective Date 20xx. 68 p. This standard specifies the requirements for a series of compact gate, globe and check valves for petroleum and natural gas industry applications. It is applicable to valves of: — nominal pipe sizes NPS 1/4, NPS 3/8, NPS 1/2, NPS 3/4, NPS 1, NPS 1 1/4, NPS 1 1/2, NPS 2, NPS 2 1/2, NPS 3, and NPS...
American Petroleum Institute (API). Seventh Edition, October 1996. 14 p. This standard covers inspection, examination, supplementary examinations, and pressure test requirements for resilient-seated, nonmetallic-seated (for example, ceramic), and metal-to-metal-seated valves of the gate, globe, plug, ball, check, butterfly types. Resilient seats are considered to be: a. soft...
American Petroleum Institute (API). Second Edition, January 1, 1995. 22 p. This specification covers material, design, fabrication, and testing requirements for fiberglass reinforced plastic (FRP) tanks. Only shop-fabricated, vertical, cylindrical tanks are covered. Tanks covered by this specification are intended for above ground and atmospheric pressure service. Unsupported cone...
American Petroleum Institute (API). Eleventh Edition, November 1, 1994. 30 p. This specification covers material, design, fabrication, and testing requirements for shop-fabricated vertical, cylindrical, aboveground, dosed top. welded steel storage tanks in various standard sizes and capacities for internal pressures approximately atmospheric, not to exceed those listed in...
American Petroleum Institute (API). Twentieth Edition October 2010, Effective Date April 1.2011. 448 p. This International Standard specifies requirements and gives recommendations for the performance, dimensional and functional interchangeability, design, materials, testing, inspection, welding, marking, handling, storing, shipment, purchasing, repair and remanufacture of...
American Petroleum Institute (API). Second Edition. 43 p. This document provides standard testing procedures for evaluating proppants used in hydraulic fracturing and gravel-packing operations. NOTE: Proppants mentioned henceforth in this document refer to sand, ceramic media, resin-coated proppants, gravelpacking media and other materials used for hydraulic fracturing and...
American Petroleum Institute (API). Fifth Edition. 86 p. API Recommended Practice 13J covers the physical properties, potential contaminants and test procedures for heavy brine fluids manufactured for use in oil and gas well drilling, completion, fracturing and workover fluids. API RP-13J provides methods for assessing the performance and physical characteristics of heavy...
American Petroleum Institute (API). Fifth Edition. 156 p. This recommended practice provides standard procedures for determining the following characteristics of oilbased drilling fluids:
a) drilling fluid density (mud weight);
b) viscosity and gel strength;
c) filtration;
d) oil, water and solids concentrations;
e) alkalinity, chloride concentration and calcium...
American Petroleum Institute (API). Sixth Edition January 2014, 58 p. When specified by the owner / operator this recommended practice should shall be considered as a guide on new tank installations and maintenance of existing tanks, used in production service for the petroleum industry. It contains recommendations for good practices in (a) the collection of well or lease...
American Petroleum Institute (API). First Edition June 2010, 40 p. The purpose of this guidance document is to identify and describe many of the current industry best practices used to minimize environmental and societal impacts associated with the acquisition, use, management, treatment, and disposal of water and other fluids associated with the process of hydraulic fracturing....
Американский нефтяной институт (API). Издание сорок четвертое, 1 октября 2007 г. Дата введения: 1 октября 2008 г. Перевод на русский язык выполнен переводческой фирмой «Интерсервис». 162 стр. Целью настоящих технических условий является создание стандарта на трубы, используемые для транспортировки газа, воды и нефти в нефтегазодобывающей и перерабатывающей промышленности....
American Petroleum Instltute (API). 12TH Edition, 1st Draft 30 May 2014 . 208 p. This Standard specifies requirements for centrifugal pumps, including pumps running in reverse as hydraulic power recovery turbines, for use in petroleum, petrochemical and gas industry process services. This Standard is applicable to overhung pumps, between-bearings pumps and vertically suspended...
Стандарт Американского нефтяного института для роторных компрессоров объёмного типа для нефтяной, нефтехимической и газовой промышленности
Редакция 3 (1997 год)
60 страниц (из 114) - не хватает половины приложений!
American Petroleum Instltute (API) Fifth Edition, Draft. 2013. 19 p. This standard specifies the requirements for metal ball valves suitable for petroleum, petrochemical and industrial applications that have: — flanged ends in sizes DN 15 through DN 600 ( NPS 1/2 through NPS 24); — butt-welding ends in sizes DN 15 through DN 600 (NPS 1/2 through NPS 24); — socket-welding ends...
American Petroleum Institute (API). Fourth Edition January 2008, Effective Date July 1.2008. 50 p. The purpose of this specification is to provide standards for polyethylene (PE) line pipe suitable for use in conveying oil, gas and non-potable water in underground, above ground and reliner applications for the oil and gas producing industries. The standard does not propose to...
American Petroleum Institute (API). First Edition February 1. 1996. Reaffirmed April 2008. 24 p. The purpose of this specification is to establish requirements to:
a. Verify the basic PR1 standard service SSVAJSV valve design.
b. Verify the basic SSVAJSV actuator design.
c. Verify the basic PR2 sandy service SSVNSV valve design.
d. To demonstrate the verification testing...
American Petroleum Instltute (API) Sixth Edition, Draft. 3.07.2013 – Ballot 2. 74p. This Standard covers methods of installation for pressure relief devices for equipment that has a maximum allowable working pressure (MAWP) of 15 psig (1.03 bar g or 103 kPA) or greater. Pressure relief valves or rupture disks may be used independently or in combination with each other to provide...
American Petroleum Institute (API), Third Edition, APRIL 2014. 106p. Recommended Practice 575
This document provides useful information and recommended practices for the maintenance and inspection of atmospheric and low-pressure storage tanks. While these maintenance and inspection guidelines may apply to other types of tanks, these practices are intended primarily for existing...
American Petroleum Institute (API). Twenty-Seventh Edition May 1. 2010, Effective Date November 1.2010. 103 p. This specification provides the requirements and guidelines for the design of steel sucker rods and pony rods, polished rods, polished rod liners, couplings and sub-couplings, fiber reinforced plastic (FRP) sucker rods, sinker bars, polished rod clamps, stuffing boxes,...
American Petroleum Institute (API).Thiteenth Edition 2013, Effective Date 2013. 115 p. This Specification provides the requirements and guidelines for the design of subsurface sucker rod pumps and their components as defined herein for use in the sucker rod lift method for the petroleum and natural gas industry. The specification covers subsurface sucker rod pump assemblies...
American Petroleum Institute (API). Eighth Edition July 1. 2005, Effective Date January 1.2006. 306 p. This International Standard specifies the technical delivery conditions for steel pipes (casing, tubing, plain-end casing liners and pup joints), coupling stock and accessories and establishes requirements for three Product Specification Levels (PSL-1, PSL-2, PSL-3). The...
American Petroleum Institute (API). Twenty-Sixth Edition, May 2011, Effective Date November 1, 2011. 64 p. This standard specifies the minimum requirements and terms of acceptance for the manufacture and testing of steel wire ropes not exceeding rope grade 2160 for the petroleum and natural gas industries. The following products are covered by this specification: - wire rope, -...
Issue: 2010
Language: English
Pages: 26
Scope:
This international standard covers design, material, face-to-face dimensions, pressure-temperature ratings, and examination, inspection, and test requirements for two types of check valves.
Type A check valves are short face-to-face as defined in Table 3 and Table 4 and can be: wafer, lug, or double flanged; single plate or...
Issue: 2009
Language: English
Pages: 30
Scope:
This International standard specifies the requirements for a heavy-duty series of bolted bonnet steel gate valves for petroleum refinery and related applications where corrosion, erosion and other service conditions would indicate a need for full port openings, heavy wall sections and large stem diameters.
This International...
API, April 2011, 58p, Second Edition. Techanical Report 938-C, Use of Duplex Stainless Steels in the Oil Refining Industry ABSTRACT Duplex stainless steels (DSS) have built up an extensive service history in many different refinery applications. Some equipment has been in service over twenty years. Today, these steels are often the most cost- effective and/or reliable alloy...
American Petroleum Institute (API). 2nd edition, December 2009. Recommended Practice 582.
This recommended practice, initiated and developed through the joint efforts of API and Process Industry Practices (PIP), provides supplementary guidelines and practices for welding and welding-related topics for shop and field fabrication, repair and modification of:
Pressure-containing...
API, September 2013, 128p. Standard 1104. 21st Ed, Welding of Pipelines and Related Facilities.
This standard covers the gas and arc welding of butt, .fillet, and socket welds in carbon and low-alloy steel piping used in the compression, pumping, and transmission of crude petroleum, petroleum products, fuel gases, carbon dioxide, and nitrogen and, where applicable, covers...
API, March 2013, 514 pages. Standard 650 Welded Tanks for Oil Storage, 12th Edition, Standard establishes minimum requirements for material, design, fabrication, erection, and testing for vertical, cylindrical, aboveground, closed- and open-top, welded carbon or stainless steel storage tanks in various sizes and capacities for internal pressures approximating atmospheric...
API, May 2014, 80p, 10th Ed.
This inspection code covers the in-service inspection, repair, alteration, and rerating activities for pressure vessels and the pressure- relieving devices protecting these vessels. This inspection code applies to all refining and chemical process vessels that have been placed in service unless specifically excluded per
This includes: a. vessels...
American Petroleum Institute (API). Second Edition, 2013, 156p.
This recommended practice provides guidance to the API authorized inspector on welding inspection as encountered with fabrication and repair of refinery and chemical plant equipment and piping. This recommended practice includes descriptions of common welding processes, welding procedures, welder qualifications,...
Second Edition - 2005
Language - English
Pages - 84
Scope
This document provides useful information and recommended practices for the maintenance and inspection of atmospheric and low-pressure storage tanks. While some of these guidelines may apply to other types of tanks, these practices are intended primarily for existing tanks that were constructed to API Spec 12A or API...
Издание 1. 1993 с дополнением 1995
Язык: Русский
Страниц: 60
Формат: PDF
Обзор:
Стандарт API 570 регламентирует процедуры контроля, ремонта, модернизации и реклассификации металлических трубопроводных систем, подвергавшихся эксплуатации.
Стандарт API 570 разработан для нефтеперерабатывающей и нефтехимической отраслей, но мо-жет использоваться, если он практически применим,...
Издание четвертое, апрель 1999
Язык: Русский
Страниц: 240
Обзор:
Данный международный стандарт включает в себя минимальные требования по смазочным системам, системам уплотнения вала нефтяного типа, системам уплотнения торцевого вала сухого газа, и систем контроля нефти для общего и особого применения. Применения в общих целях ограничиваются системами смазки. Эти системы могут...
Fifth Edition, February 2003
Language: English
Pages: 102
Scope:
This standard covers the minimum requirements for special-purpose, enclosed, precision single- and double-helical one- and two-stage speed increasers and reducers of parallels haft design for petroleum, chemical and gas industry services. This standard is primarily intended for gear units that are in continuous...
American Petroleum Institute (API) Forty-Fifth Edition, December 2012. 192p. Effective date: july 1, 2013 This Standard specifies requirements for the manufacture of two product specification levels (PSL 1 and PSL 2) of seamless and welded steel pipes for use in pipeline transportation systems in the petroleum and natural gas industries. This Standard is not applicable to cast...
Effective date: August 1, 2015
Published: August 1, 2014
Number of Pages: 122 (включая Errata 1, 2)
This specification defines the requirements for the design, manufacturing, assembly, testing, and documentation of ball, check, gate, and plug valves for application in pipeline and piping systems for the petroleum and natural gas industries. This specification is not...
Восьмое издание. декабрь 2007 г. Принятие системы менеджмента качества должно быть стратегическим решением организации. На проектирование и внедрение системы менеджмента качества организации оказывают влияние различные потребности, специфические цели, выпускаемая продукция, применяемые процессы, а также размер и структура организации. Настоящий международный стандарт не...
American Petroleum Institute (API). First Edition. December 2003. 114p. The ASME and API design codes and standards for pressurized equipment provide rules for the design, fabrication, inspection, and testing of new pressure vessels, piping systems, and storage tanks. These codes do not address equipment deterioration while in service and that deficiencies due to degradation or...
192 стр.
API 610 на русском языке
Стандарт идентичен ISO 13709:2003
Настоящий международный стандарт разработан на основе стандарта API, 8ое издание, 1995, с
намерением, чтобы 9ое издание стандарта API 610 было бы таким же, как и данный международный стандарт.
ANSI/API Standard, API Publishing Services, 1220 L Street, N.W., Washington, D.C. 20005, 2008. - 206 sh. This International Standard is applicable to pressure-relieving and vapour-depressuring systems. Although intended for use primarily in oil refineries, it is also applicable to petrochemical facilities, gas plants, liquefied natural gas (LNG) facilities and oil and gas...
Четвертое издание, 2012, 273 стр., на английском языке. API 682 (ISO 21049) описывает системы уплотнения вала для центробежных и роторных насосов. Стандарт представляет собой комплекс организационно-технических мероприятий по разработке и изготовлению уплотнительных систем с торцовыми уплотнениями повышенной надежности и безопасности. Регламентирует типы, компоновки...
Данный стандарт вступает в силу с даты, опубликованной на обложке, но может использоваться начиная с момента поступления. Стандарты, на которые в нем даются ссылки, могут быть заменены другими международными и национальными стандартами, если будет показано, что они удовлетворяют требованиям стандартов, на которые даются ссылки, или превышают их. Изготовители, использующие...
American Petroleum Institute (API), Washington, USA, 1nd edition (2000), 90 pages.
This Addendum specifically covers inferred mass measurement systems utilizing flow computers as the tertiary flow calculation device and either turbine or displacement type meters, working with on-line density meters, as the primary measurement devices. The Scope does not include system using...
American Petroleum Institute (API), Washington, USA, 1nd edition (1993), reaffirmed (2005), 46 pages.
This standard describes the minimum specifications for electronic gas measurement systems used in the measurement and recording of flow parameters of gaseous phase hydrocarbons. Topics covered include definitions, calculations, algorithms, data availability, audit and reporting...
American Petroleum Institute (API), Washington, USA, 1993, 1nd edition, 33 pages.
This standard describes the minimum specifications for electronic gas measurement systems used in the measurement and recording of flow parameters of gaseous phase hydrocarbons. Topics covered include definitions, calculations, algorithms, data availability, audit and reporting requirements,...
American Petroleum Institute (API), Washington, USA, 2000, 4nd edition, 70 pages.
This part outlines the specification and installation requirements for the measurement of single-phase, homogeneous Newtonian fluids using concentric, square-edged, flange-tapped orifice meters. It provides specifications for the construction and installation of orifice plates, meter tubes, and...
American Petroleum Institute (API), Washington, USA, 2005, 1st draft, 2nd edition, 22 pages.
API MPMS 5.8 describes methods for the installation and operation of Ultrasonic Flow Meters (UFMs) when they are used to measure liquid hydrocarbons. The scope of this document will define the application criteria for UFMs and address the appropriate considerations regarding the liquids...
Спецификация на испытание арматуры на пожаростойкость, включая 2 поправки 2006 и 2008 года Fire Test for Valves, Includes Errata 1(2006) and 2 (2008) American Petroleum Institute (API), 3 Edition, April 1999. 18стр It is the purpose of this document to establish the requirements for testing and evaluating the pressure-containing performance of API Specs 6A amd 6D valves when...
23-е издание. Дата вступления в силу - 1 июля 2008 Формат - PDF. Язык - Русский. Объем - 93 страницы Настоящий Международный стандарт определяет требования и представляет рекоменда- ции к проектированию, производству, проверке и документации шаровых, предохранитель- ных клапанов, шиберных задвижек и крановых клапанов для применения в трубопроводных системах, соответствующих...
Американский нефтяной институт (API). Издание сорок четвертое, 1 ноября 2007 г. Дата введения: 1 октября 2008 г. Перевод на русский язык. 162 стр. Целью настоящих технических условий является создание стандарта на трубы, используемые для транспортировки газа, воды и нефти в нефтегазодобывающей и перерабатывающей промышленности. Настоящий Стандарт устанавливает требования к двум...
API Spec 5CT-2011 Обсадные и насосно-компрессорные трубы. Технические условия Американский нефтяной институт (API). Издание девятое, июль 2011 г. Дата введения: 1 января 2012 г. Перевод на русский язык. 287 стр. Данный стандарт устанавливает технические условия поставки стальных труб (обсадных, насосно-компрессорных и укороченных труб), трубных заготовок для муфт, заготовок для...
American Petroleum Instltute (API), Second Edition (ballot draft), February 2012, 186 pages. This document furnishes recommendations about the selection and design of process measurement systems. Further, it supplies information on their implementation and commissioning. It covers the entire instrumentation life cycle including selection, design, installation, commissioning and...
American Petroleum Institute (API). First edition, March 2001. This recommended practice, initiated and developed through the joint efforts of API and Process Industry Practices (PIP), provides supplementary guidelines and practices for welding and welding-related topics for shop and field fabrication, repair and modification of:
Pressure-containing equipment (such as pressure...
API Standard 650 Welded Tanks for Oil Storage, 11th Edition, Includes Addendum 1 (2008), Addendum 2 (2009) EFFECTIVE DATE: MAY 1, 2010; 438 pages
Standard establishes minimum requirements for material, design, fabrication, erection, and testing for vertical, cylindrical, aboveground, closed- and open-top, welded carbon or stainless steel storage tanks in various sizes and...
This International Standard specifies the requirements for couplings for the transmission of power between the rotating shafts of two machines in special-purpose applications in the petroleum, petrochemical and natural gas industries. Such applications are typically in large and/or high speed machines, in services that can be required to operate continuously for extended periods,...
API RP 2214 FOURTH EDITION, JULY 2004. 12 pags. This publication emphasizes that the use of nonferrous hand tools, sometimes referred to as nonsparking tools, is not warranted as a fire prevention measure in petroleum operations.
THIRD EDITION, DECEMBER 2003. 18 pags. This RP provides information concerning the potential for ignition of hydrocarbons that are exposed to hot surfaces in the open air
American Petroleum Instltute (API) Second Edition, December 2009. 38 p. This Standard provides supplementary guidelines and practices for welding and welding related topics for shop and field fabrication, repair and modification of the following: a) pressure-containing equipment such as pressure vessels, heat exchangers, piping, heater tubes, and pressure boundaries of rotating...
169 c. Design of Risers for Floating Production Systems (FPSs) and Tension-Leg Platforms (TLPs) Exploration and Production Department RECOMMENDED PRACTICE 2RD FIRST EDITION, JUNE 1998 The design of risers for Floating Production Systems( FPSs) and Tension-Leg Platforms (TLPs) requires recognition that risers form a subsystem that is an integral part of the total system. The...
An American National Standard. American Petroleum Institute (API) Forty-fourth Edition, October 1, 2007, Effective Date: October 1, 2008. Errata, January 2009. Addendum, February 2009. 176p. This International Standard is the result of harmonizing the requirements of the following standards: - API Spec 5L; - ISO 3183-1:1996; - ISO 3183-2:1996; - ISO 3183-3:1999. This Standard...
An American National Standard. American Petroleum Institute (API). First Edition, August 2009, Effective Date August 1, 2010. 122 p. This Standard specifies the technical delivery conditions for steel drill-pipes with upset pipe-body ends and weld-on tool joints for use in drilling and production operations in petroleum and natural gas industries for three product specification...
American Petroleum Institute (API). Ninth Edition, July 2011, Effective Date January 1, 2012. 284 p. This Standard specifies the technical delivery conditions for steel pipes (casing, tubing and pup joints), coupling stock, coupling material and accessory material and establishes requirements for three Product Specification Levels (PSL-1, PSL-2, PSL-3). The requirements for...
Настоящий стандарт распространяется на проектирование и строительство сварных надземных резервуаров-хранилищ низкого давления большой вместимости, выполненных из углеродистой стали (включая плоскодонные резервуары), имеющих одну вертикальную ось вращения. Настоящий стандарт не распространяется на процедуры проектирования резервуаров, имеющих стенки, формы которых не могут быть...
API RP 14G:2007 Recommended Practice for Fire Prevention and Control on Fixed Open-type Offshore Production Platforms
American Petroleum Institute (API). Fourth Edition. April 2007. 46 p. This publication presents recommendations for minimizing the likelihood of having an accidental fire, and for designing, inspecting, and maintaining fire control systems. It emphasizes the need...
American Petroleum Institute (API). Third Edition. January 2005. 40 p. The scope of this recommended practice is specifically limited to tanks associated with marketing. refining, pipeline and sinlilar facilities containing Class I or Class II petroleum liquids.
American Petroleum Institute (API). Sixth Edition, July 2002 . 16 p. The recommendations provided herein apply to the transportation on railcars of API Specification 5L steel line pipe in sizes 23/8 and larger in lengths longer that single random. The recommendations of Section 4 concerned with load stresses are exclusively applicable to API line pipe having diameter to thickness...
American Petroleum Institute (API). May 2007. 68 p. This interim document presents hurricane-driven metocean conditions (wind, wave, current and surge) for use with and reference by other API standards. These conditions are intended to replace the conditions documented in Sections
2.3.4.c and
17.6.2.a of API RP 2A-WSD, 21st Edition and Appendix C4 of ISO 19901-1.
Американский нефтяной институт (API). Издание шестое, сентябрь 2004 г. Перевод на русский язык. 20 стр. Данный стандарт распространяется на конструкцию, материалы, строительные размеры, параметрические ряды давление-температура и на требования по контролю, внешнему осмотру и испытаниям для обратных затворов
Американский нефтяной институт (API). Издание пятое, июнь 2002 г. Перевод на русский язык. 50 стр. Настоящий стандарт является спецификацией для заказа стальной предохранительной арматуры с фланцами. Основными требованиями, предъяляемыми к пружинным предохранительным клапанам пямого действия и управляемойпредохранительным клапанам непрямого действия, являются следующие: а....
Американский нефтяной институт (API). Издание второе, декабрь 2005 г. Перевод на русский язык. 22 стр. Настоящий документ обеспечивает руководящие указания для восстановления толстостенных задвижек изготовленных из углеродистой стали, ферритового сплава, нержавеющей стали и никелевого сплава. Указания, содержащиеся в данном документе применимы к арматуре с фланцами и под приварку...
Американский нефтяной институт (API). Издание восьмое, май 2004 г. Перевод на русский язык. 15 стр. Настоящий стандарт охватывает вопросы технического осмотра, испытания, дополнительного испытания и требований к гидравлическим испытаниям на герметичность клапанов с упругим седлом, с неметаллическим седлом (т.е. керамическим) и седлом на металлическом контакте следующих типов:...
American Petroleum Institute (API). Second Edition, December 2000. 58p. This recommended practice describes the inspection and repair practices for automatic pressure-relieving devices commonly used in the oil and petrochemical industries. As a guide to the inspection and repair of these devices in the user's plant, it is intended to ensure their proper performance. This...
American Petroleum Institute (API). First Edition, September 1995. 69p. This recommended practice covers the performance requirements and considerations for the selection, specification, installation, and testing of process instrumentation and control systems. Control centers as used in the petroleum industry are also covered. This practice is not intended to be used as a...
American Petroleum Institute (API). First Edition, October 1994. 49p. This document reviews the recommended practices for the installation of electronic and pneumatic measurement and control-signal transmission systems. These methods are based on the assumption that the field devices, such as measuring transmitters, transducers, valve positioners, control valves, and other devices...
American Petroleum Institute (API). Third Edition, May 2001. 208p. This standard covers the minimum requirements for the design, materials, fabrication, inspection, testing, preparation for shipment, and erection of fired heaters, air preheaters, fans and burners for general refinery service. A fired heater is an exchanger that transfers heat from the combustion of fuel to...
American Petroleum Institute (API). First Edition, December 2000. 39p. This recommended practice describes commonly used practices for the opportunity identification, justification, project management, implementation and maintenance of advanced control system applications in refinery services. This practice is not intended to spec@ the use or selection of any particular technique...
Specification, American petroleum institute, 2005, p. 28
scope
normative references
terms and definitions
test conditions
fire test method
performance
quallification of other valves by represantative size, pressuare rating and materials of construction
Specifiication, American petrolium institute, april 30, 2002, p. 48 Стандарт API 5D Бурильные трубы на английском языке. Scope Definitions Process of manufacture Chemical composition Mechanical properties requireements testing Requirements for demention, weights, lengths, and defects pipe ends pipe inspection marking and coatings minimum facility requiremenst for various...
American Petroleum Institute (API) and The Institute of Petroleum, London (IP). Third Edition, April 2001. 49p. ISBN: 0 85293 280 4. This publication specifies dimensions, coupling action, activation, and other requirements to achieve the necessary operational requirements and full interchangeability between components from manufacturers of hydrant pit valve assemblies and...
American Petroleum Institute (API) and The Institute of Petroleum, London (IP). February 2001. 50p. ISBN: 0 85293 282 0. This publication specifies the minimum requirements for a filter/separator system to qualify to API/IP 1581 by similarity. This publication applies to two-stage (filter and separator) and the filter/separator stages of multi-stage filter/separator systems....
American Petroleum Institute (API) and The Institute of Petroleum, London (IP). Fifth Edition, July 2002. 50p. ISBN: 0 85293 371 1This publication specifies the minimum performance and mechanical requirements and the testing and qualification procedures for aviation jet fuel filter/separators with flow rates ranging up to 9 500 lpm (2 500 gpm). This specification defines...
An American National Standard. American Petroleum Institute (API). First Edition, November 2001. 86p. This standard is applicable to pipeline systems used to transport hazardous liquids as defined in Title CER
195.2. The use of this standard is not limited to pipelines regulated under Title 49 CFR 195.1, and the principles embodied in integrity management are applicable to all...
American Petroleum Institute (API). Third Edition, March 2000. 18p. A pipeline supervisory control center is a center for monitoring and controlling a pipeline system. This publication presents six lists of general considerations appropriate for developing or revamping a pipeline supervisory control center. The lists are not all-inclusive but should help stimulate further,...
American Petroleum Institute (API). Seventh Edition, March 2001. 104p. This document presents recommendations for designing, installing, and testing a basic surface safety system on an offshore production platform. The basic concepts of a platform safety system are discussed and protection methods and requirements of the system are outlined.
American Petroleum Institute (API). First Edition, March 2004. 42p. This recommended practice summarizes the results of experimental tests and actual data acquired from operating plants to establish practical operating limits for carbon and low alloy steels in hydrogen service at elevated temperatures and pressures. The effects on the resistance of steels to hydrogen at elevated...
American Petroleum Institute (API). First Edition, December 2000. 20p. This recommended practice presents materials and fabrication requirements for new 2–1/4Cr and 3Cr steel heavy wall pressure vessels for high temperature, high pressure hydrogen service. It applies to vessels that are designed, fabricated, certified and documented in accordance with ASME Code Section VIII,...
American Petroleum Institute (API). First Edition, July 2004. 42p. This recommended practice provides guidance to engineering and plant personnel on equipment and piping design, material selection, fabrication, operation, and inspection practices to manage corrosion and fouling in the wet sections of hydroprocessing reactor efßuent systems. The reactor efßuent system includes all...
American Petroleum Institute (API). First Edition, June 2006. 24p. The purpose of this interim recommended practice is to present an interim approach to siting Jackup Mobile Offshore Drilling Units (MODUs) and to recommend certain operational procedures to enhance Jackup survivability and stationkeeping during hurricane season in the Gulf of Mexico during drilling, workover, and...
American Petroleum Institute (API). First Edition, May 2006. 50p. This document provides guidance and processes and, when combined with an understanding of the environment at a particular location, the characteristics of the unit being utilized, and other factors, may be used to enhance operational integrity in the survival condition. The information presented herein is premised...
American Petroleum Institute (API). First Edition, August 2006. 96p. This Recommended Practice is intended to serve as a guide for managing annular casing pressure in offshore wells. Although the prevention of annular casing pressure is very important, it is beyond the scope of this document. Prevention of annular casing pressure is planned to be addressed in API RP 65, Part
2....
American Petroleum Institute (API). First Edition, August 2007. Effective Date: February 2008. 32p. The purpose of this document is to provide the user with recommended ‘field’ methods of sampling, sample handling and analysis for high water content streams up to 50 % water on a volumetric basis. In particular, this RP was developed giving consideration to offshore installations...
American Petroleum Institute (API). First Edition, September 2005. 84p. Specifically this document will address in depth the question of how the user measures (multiphase) flow rates of oil, gas, water, and any other fluids that are present in the effluent stream of a single well. This requires the definition not only of the methodology which is to be employed, but also the...
American Petroleum Institute (API). First Edition, April 2000. 63p. This industry standard provides a functional description of onshore gas gathering pipelines for the sole purpose of providing users with a practical guide for determining the application of the definition of gas gathering in the federal Gas Pipeline Safety Standards, 49 CFR Part 192, and state programs...
American Petroleum Institute (API). First Edition, May 2004. 26p. This publication is intended to assist the offshore oil and natural gas drilling and producing operators and contractors in assessing security needs during the performance of oil and natural gas operations. The offshore oil and natural gas industry uses a wide variety of contractors in drilling, production, and...
American Petroleum Institute (API). First Edition, March 2003. 28p. This publication is intended to assist the offshore oil and natural gas drilling and producing operators and contractors in assessing security needs during the performance of oil and natural gas operations. The offshore oil and natural gas industry uses a wide variety of contractors in drilling, production, and...
American Petroleum Institute (API). Twelfth Edition, June 2005. 40p. This recommended practice covers typical wire rope applications for the oil and gas industry. Typical practices in the application of wire rope to oil field service are indicated in Table 1, which shows the sizes and constructions commonly used. Because of the variety of equipment designs, the selection of...
American Petroleum Institute (API). First Edition, February 2005. 20p. This Recommended Practice may supplement the API equipment specifications for large cross section and critical components. The recommend practice described herein suggests the requirements for batch-type bath quench and water spray quench-type heat treating practices
American Petroleum Institute (API). First Edition, February 2006. 22p. This Recommended Practice (RP) provides guidelines for the repair and remanufacture of steel ball, check, gate, and plug valves normally used in pipeline applications, as defined by API Spec 6D. This RP covers repair or remanufacturing of end user’s (owner’s) valves for continued service in the owner’s...
American Petroleum Institute (API). First Edition, September 2004. 60p. This standard on SCADA security provides guidance to the operators of Oil and Gas liquid pipeline systems for managing SCADA system integrity and security. The use of this document is not limited to pipelines regulated under Title 49 CFR 195.1, but should be viewed as a listing of best practices to be employed...
American Petroleum Institute (API). First Edition, August 2005. 50p. This Standard covers the use of in-line inspection systems for onshore and offshore gas and hazardous liquid pipelines. This includes, but is not limited to, tethered or free flowing systems for detecting metal loss, cracks, mechanical damage, pipeline geometries, and pipeline location or mapping, The Standard...
American Petroleum Institute (API). First Edition, July 2002. Effective Date: January, 2003. 35p. This Standard provides requirements for packers and bridge plugs for use in the petroleum and natural gas industry. Application of this International Standard is limited to those products meeting the definition of a packer or bridge plug intended for petroleum and natural gas industry...
American Petroleum Institute (API). Twelfth Edition, June 2006. Effective Date: December, 2006. 86p. This specification covers rod pumps and tubing pumps in commonly used bore sizes. Sufficient dimensional requirements are provided to assure interchangeability and standardization of all component parts; however, details of design are not specified. Standard materials are specified
American Petroleum Institute (API). Seventh Edition, August 2001. Effective Date: February 2002. 38p. This specification covers filament wound (FW) and centrifugally cast (CC) fiberglass line pipe and fittings for pipe in diameters up to and including 24 in. in diameter and up to and including 1000 psig cyclic operating pressures. In addition, at the manufacturer's option, the...
An American National Standard. American Petroleum Institute (API). Eleventh Edition, August 2007. Effective Date: March 2008. 36p. This Standard provides the requirements for lock mandrels and landing nipples within the production/injection conduit for the installation of flow control or other equipment used in the petroleum and natural gas industries. It includes the interface...
American Petroleum Institute (API). Eighth Edition, October 2008. Effective Date: April 2009. 40p. This specification covers minimum requirements for the design, fabrication, and shop testing of oilfield indirect type fired heaters used in the production of oil, gas, and their associated fluids. They are usually located at some point on the producing flow-line between the wellhead...
American Petroleum Institute (API). Third Edition, July 2003. 24p. This recommended practice addresses the permanent marking of liquid petroleum pipeline transportation facilities. It covers the design, message, installation, placement, inspection, and maintenance of markers and signs on pipeline facilities located onshore and at inland waterway crossings. Markers and signs...
American Petroleum Institute (API). Second Edition, March 2001. 60p. Test site recommendations (Section 3): This section outlines the equipment needed for testing valves to determine the following: a. Valve flow coefficients (Cv). b. Pressure drop ratio factor (Xt). c. Gas-lift valve performance curves.
American Petroleum Institute (API). First Edition, August 2000. 106p. This API Guidance Document for the Qualification of Pipeline Personnel was developed by the API’s subcommittee on Training to help pipeline operators comply with the Research and Special Program Administration’s (RSPA) Final Rule on Pipeline Safety: Qualification for Pipeline Personnel.
American Petroleum Institute (API). Fifteenth Edition, April 2002. 84p. This publication describes the API Engine Oil Licensing and CertiÞcation System (EOLCS), a voluntary licensing and certiÞcation program designed to deÞne, certify, and monitor engine oil performance deemed necessary for satisfactory equipment life and performance by vehicle and engine manufacturers. Engine oil...
American Petroleum Institute (API). Sixth Edition, March 2002 . Effective Date: September 1, 2002. 24p. This standard provides minimum performance requirements, test procedures and marking requirements for bowspring casing centralizers for the petroleum and natural gas industries. The requirements contained herein are limited, but are deemed adequate for use in oil field...
American Petroleum Institute (API). Twenty-third Edition, April 2002. Effective Date: October 1, 2002 59p. This standard specifies requirements and gives recommendations for eight classes of well cements, including their chemical and physical requirements and procedures for physical testing. This standard is applicable to well cement Classes A, B, C, D, E and F, which are the...
An American National Standard. American Petroleum Institute (API). Second Edition , July 2006. 254p. This standard gives requirements and recommendations for the design, analysis, materials, fabrication, testing and operation of subsea completion/workover (C/WO) riser systems run from a floating vessel. It is applicable to all new C/WO riser systems and may be applied to...
An American National Standard. American Petroleum Institute (API). First Edition , August 2004. 26p. This standard provides calculations for determining centralizer spacing, based on centralizer
performance and desired standoff, in deviated and dogleg holes in wells for the petroleum and natural gas industries. It also provides a procedure for testing stop collars and reporting...
An American National Standard. American Petroleum Institute (API). Fifth Edition. July 2008. 162p. This document recommends minimum requirements and guidelines for the design, installation, and maintenance of electrical systems on fixed and floating petroleum facilities located offshore. For facilities classified as Zone 0, Zone 1 or Zone 2, reference API 14FZ, Recommended...
An American National Standard. American Petroleum Institute (API). Twenty-Third Edition , April 2008. Addendum 2, August 2011. 106p. This Standard specifies requirements and provides recommendations for the design, manufacturing, testing and documentation of ball, check, gate and plug valves for application in pipeline systems meeting the requirements of ISO 13623 for the...
API Standard 608, 3-е издание, август 2002 на русском языке (сканированная копия). Данный стандарт распространяется на краны шаровые металлические фланцевые, резьбовые и с патрубками под приваркую, используемые как запорная арматура для номинальных размеров трубы от 1/2 до 12 дюймов - для фланцевых, и от 1/2 до 2 дюймов для резьвовых и приварных.
American Petroleum Institute (API). Second Edition, 201X. 89p. This Standard addresses riser systems that are part of a floating production system (FPS). Guidelines for design, construction, installation, operation and maintenance of floating production systems (FPSs) are in API 2FPS. A riser is a subsystem in a floating production system
American Petroleum Institute (API). First Edition, 2012. 61p. This recommended practice covers the basic requirements and their associated references needed to effectively and safely perform inspection activities during construction of new onshore pipelines. Use of this document will provide the basis for what construction inspectors need to know and where to find detailed...
API RP 5B1
1. Рекомендованная практика по контролю резьбы обсадных, насосно-коспрессорных и трубопроводных труб. 5-е издание, 1999 год, русский язык.
Настоящая рекомендованая практика представлена в качестве руководящего и учебного средства для инспекторов трубных заводов, независимых инспекторов и пользователей, заинтересованных в совершенствовании навыков контроля резьбы.
American Petroleum Institute (API). Third Edition, October 2005. 190p. The purpose of these recommended practices is to present a rational method for analyzing, designing or evaluating station-keeping systems used for floating units. This method provides a uniform analysis tool which, when combined with an under-standard of the environment at a particular location, the...
An American National Standard. American Petroleum Institute (API).This recommended practice was prepared under the direction of the API Safety and Fire
Protection Subcommittee. This third edition of API 2028
Flame Arresters in Piping Systems
has been extensively rewritten and updated from the previous edition. Appendices to the document
are intended to provide additional...
210 стр. API 682 - Системы уплотнения вала для центробежных и роторных насосов. Third Edition, September 2004. This international Standard specifies requirements and gives recommendations for sealing systems for centrifugal and rotary pumps used in the petroleum, natural gas and chemical industries. It is applicable mainly for hazardous, flammable and/or toxic services where a...
142 стр. API Standart 685 - Герметичные бессальниковые центробежные насосы для нефтедобычи при эксплуатации в тяжелом режиме работы в химической и газовой промышленности. First Edition, October 2000 This standard is based on the accumulated knowledge and experience of manufacturers and users of sealless centrifugal pumps. The objective of this publication is to provide a...
An American National Standard. American Petroleum Institute (API). Eleventh Edition, October 2001. 47p. This Standard specifies the requirements for a heavy duty series of bolted bonnet steel gate valves for petroleum refinery and related applications where corrosion, erosion and other service conditions indicate a need for full port openings, heavy wall sections and extra large...
American Petroleum Institute (API). First Edition, October 2009. Addendum 1, 2012. 52p. This recommended practice (RP) addresses the requirements for the use of high integrity pressure protection systems (HIPPS) for subsea applications. API 14C, IEC 61508, and IEC 61511 specify the requirements for onshore, topsides, and subsea safety instrumented systems (SIS’s) and are...
An American National Standard. American Petroleum Institute (API). Eleventh Edition, October 2005. Effective Date: May 1, 2006. 89p. This Standard provides the minimum acceptable requirements for subsurface safety valves (SSSVs). It covers subsurface safety valves including all components that establish tolerances and/or clearances which may affect performance or...
An American National Standard. American Petroleum Institute (API). Third Edition, July 2008. Effective Date: January 1, 2009. 85p. This Standard 13628 defines the technical requirements for safe, dimensionally and functionally interchangeable flexible pipes that are designed and manufactured to uniform standards and criteria. Minimum requirements are specified for the design,...
An American National Standard. American Petroleum Institute (API). Fifth Edition. October 2005. 40p. This Standard establishes requirements and provides guidelines for configuration, installation, test, operation and documentation of subsurface safety valve (SSSV) systems. In addition, this International Standard establishes requirements and provides guidelines for selection,...
American Petroleum Institute (API). 2010. 42p. This publication was created by an API subcommittee. The members of this subcommittee were predominantly operators of liquids pipelines, but included participation from operators of gas systems, as well as members from the alarm management and control systems communities, academia, and US DOT/PHMSA representatives. This document is...
American Petroleum Institute (API). Second Edition. 2010. 71p. The scope of this RP covers the development, implementation, evaluation, and documentation of public awareness programs associated with the normal operation of existing pipeline systems and facilities, including the following:
— transmission pipelines,
— local distribution systems,
— gathering lines.
American Petroleum Institute (API). Third Edition. 77p. The purpose of this standard is to assist owners and contractors in developing, improving and maintaining their mutual safety programs. Widely diverse contractor functions and uses may include resident, non-resident, long-term and short-term contractors. These have in common the need for effective safety programs to protect...
American Petroleum Institute (API). Second Edition. Ballot
2. Aug. 2009. 77p. This specification was formulated to provide for safe and functionally interchangeable surface and subsea choke and kill systems equipment utilized for drilling oil and gas wells. Choke and kill system components shall be in accordance with the applicable sections of this specification.
American Petroleum Institute (API). Seventh Edition. Ballot 1. 146p. This specification provides requirements for design, construction, and testing of new offshore pedestal-mounted cranes. For the purposes of this specification, offshore cranes are defined as pedestal-mounted elevating and rotating lift devices for transfer of materials or personnel to or from marine vessels,...
American Petroleum Institute (API). Fifth Edition. 2012. 64p. This Standard specifies a standard procedure for assessing and modifying the performance of solids control equipment systems commonly used in the field in petroleum and natural gas drilling fluids processing
American Petroleum Institute (API). Third Edition, July 2002. 44p. Each component of the ESP system (pump, motor, intake, seal or protector, cable, switchboard, etc.) is discussed in some detail as far as what must be considered for the best selection at a desired rate and well conditions. Examples are given to illustrate the basic design procedure and illustrate how PVT...
American Petroleum Institute (API). Fourth Edition. May 1996. Reaffirmed, March 2006. 24p. This recommended practice provides a guide for planning, designing, and constructing heliports for fixed offshore platforms. It includes operational consideration guidelines, design load criteria, heliport size, marking recommendations, and other heliport design recommendations.
American Petroleum Institute (API). Fifteenth Edition, May 1, 1993. 52p. This specification covers physical properties and test procedures for materials manufactured for use in oil well drilling fluids. The materials covered are barite, hematite, bentonite, nontreated bentonite, attapulgite, sepiolite, OCMA grade bentonite, technical-grade lowviscosity carboxymethylcellulose...
An American National Standard. American Petroleum Institute (API). Third Edition, October 2005. 28p. This recommended practice provides guidance on achieving effective corrosion control in aboveground storage tanks by application of tank bottom linings. It contains information pertinent to the selection of lining materials, surface preparation, lining application, cure, and...
American Petroleum Institute (API). Fourth Edition. 132p. The purpose of this standard is to provide requirements that can serve as a guide for installation and testing of blowout prevention equipment systems on land and marine drilling rigs (barge, platform, bottom-supported, and floating). A blowout preventor system is comprised of a combination of various components. The...
American Petroleum Institute (API). First Edition. Ballot 1 - April 2011. 147p. The complexity of DW operations requires a thorough understanding of its well design criteria and associated equipment. This recommended practice (RP) identifies considerations for use in DW well design, drilling, and completions operations for reference by drilling and completion engineers and...
American Petroleum Institute (API). Draft. Third Edition. Third Ballot—Closes 03/02/2011. 103p. This recommended practice covers the inspection practices for fired boilers and process heaters (furnaces) used in petroleum refineries and petrochemical plants. The practices described in this document are focused to improve equipment reliability and plant safety by describing the...
American Petroleum Institute (API). Draft. Second Edition. April 2011. 174p. This document recommends minimum requirements and guidelines for the design, installation, and maintenance of electrical systems on fixed and floating petroleum facilities located offshore. For facilities classified as Division 1 or Division 2, reference API RP 14F, Recommended Practice for Design,...
An American National Standard, American Petroleum Institute (API). Twenty-Second Edition. 200X. 324p. This publication serves as a guide for those who are concerned with the design and construction of new fixed offshore platforms and for the relocation of existing platforms used for the drilling, development, production, and storage of hydrocarbons in offshore areas. In addition,...
An American National Standard, American Petroleum Institute (API). Draft. Second Edition. Ballot 2 – December 2010. 227p. This standard provides requirements and guidance for the structural design and/or assessment of floating offshore platforms used by the petroleum and natural gas industries to support the following functions: - production; - storage and/or offloading; -...
An American National Standard, American Petroleum Institute (API). Draft. First Edition. 57p. This standard is considered identical to the English version of ISO 17078-4:2010. This part of ISO 17078 provides informative documentation to assist the user/purchaser and the supplier/manufacturer in specification, design, selection, testing, calibration, reconditioning, installation...
An American National Standard, American Petroleum Institute (API). Fourth Edition, XXX 2010. 188p. This standard is considered identical to the English version of ISO 13628-5:2009. This part of ISO 13628 specifies requirements and gives recommendations for the design, material selection, manufacture, design verification, testing, installation and operation of umbilicals and...
American Petroleum Institute (API). XXX Teenth Edition, June 2010. 71p. This Specification covers dimensions, tolerances and marking requirements for API threads and the gauges that control the
acceptance criteria for the threads. Thread element gauges, instruments and requirements for the inspection of threads for line pipe, round thread casing, and buttress casing connections...
American Petroleum Institute (API). First Edition,December 2006. Effective Date: June 2007. 26p. This specification covers two grades of high strength steel plate for use in welded construction of offshore structures, in selected critical portions which must resist impact, plastic fatigue loading, and lamellar tearing. Grade 50 is covered in thicknesses up to 6 in. (150 mm)...
An American National Standard, American Petroleum Institute (API). Fifth Edition, March 2002. 126p. This API standard is identical with English version of ISO
13706. This Standard gives requirements and recommendations for the design, materials, fabrication, inspection, testing and preparation for shipment of air-cooled heat exchangers for use in the petroleum, petrochemical and...
American Petroleum Institute (API). Draft. First Edition. 29p. This standard specifies the requirements for a heavy-duty series of bolted bonnet steel globe valves for petroleum refinery and related applications where corrosion, erosion and other service conditions would indicate a need for heavy wall sections and large stem diameters.
An American National Standard, American Petroleum Institute (API). Eighth Edition, August 2007. 52p. This International Standard specifies requirements and gives recommendations for the mechanical design, material selection, fabrication, inspection, testing and preparation for shipment of shell-and-tube heat exchangers for the petroleum, petrochemical and natural gas industries
An American National Standard, American Petroleum Institute (API). Draft. First Edition. 40p. This standard shall become effective on the date printed on the cover but may be used voluntarily from the date of distribution. This standard is considered identical to the English version of ISO 15590-1
American Petroleum Institute (API). First Edition, November 2008. 86p. The purpose of these recommended practices is to provide information that can serve as a guide for planning, installation, operation and testing of underbalanced drilling equipment systems on land and offshore drilling rigs
[barge, platform, bottom-supported, and floating with surface blowout preventers (BOP)...
An American National Standard, American Petroleum Institute (API). Draft. Ninth Edition. 279p. This standard replaces API Specification 5CT Eighth Edition. This standard shall become effective on the date printed on the cover but may be used voluntarily from the date of distribution. This standard is considered identical to the English version of ISO 11960.
An American National Standard, American Petroleum Institute (API). Draft. Twenty-fourth Edition. 50p. This standard replaces API Specification 10A, 23rd edition. This standard shall become effective on the date printed on the cover but may be used voluntarily from the date of distribution. This standard is considered identical to the English version of ISO 10426-
1. In this...
Американский нефтяной институт (API). Издание сорок третье, март 2004 г. Дата введения: 4 октября 2004 г. Перевод на русский язык. 196 стр. Целью настоящих технических условий является создание стандарта на трубы, используемые для транспортировки газа, воды и нефти в нефтегазодобывающей и перерабатывающей промышленности. Настоящие техусловия распространяются на стальные...
American Petroleum Institute (API). Date: 2009-10-05. 84p. This API document is a Draft Standard. The objective of this Recommended Practice (RP) is to provide a basic understanding of and guidance about drilling fluid rheology and hydraulics, and their application to drilling operations. The purpose for updating the existing Recommended Practice, last published in May 2003, is to...
An American National Standard. American Petroleum Institute (API) Forty-fourth Edition, October 1, 2007, Effective Date: October 1, 2008. 162p. This International Standard specifies requirements for the manufacture of two product specification levels (PSL 1 and PSL 2) of seamless and welded steel pipes for use in pipeline transportation systems in the petroleum and natural gas...
American Petroleum Institute (API). Seventh Edition October 1. 2001, Effective Date April 1.2002. 124p. This International Standard specifies the technical delivery conditions for steel pipes (casing, tubing, plain and casing lines and pup-joints) and accessories. This International Standard is applicable to the following connections in accordance with ISO 10422 or API Spec 5B:...
American Petroleum Institute (API). Draft Second Edition, Third Ballot-Closes 03/25/2011. 149p. This recommended practice provides guidance to the API authorized inspector on welding inspection as encountered with fabrication and repair of refinery and chemical plant equipment and piping. This recommended practice includes descriptions of common welding processes, welding...
American Petroleum Institute (API). Guidance Document. First Edition, October 2009. 44p. The purpose of this guidance document is to provide guidance and highlight industry recommended practices for well
construction and integrity for wells that will be hydraulically fractured. The guidance provided here will help to ensure that shallow groundwater aquifers and the environment...
API 650 (American Petroleum Institute) 11-ое издание, июнь 2007. Сварные стальные резервуары для хранения нефтепродуктов. На русском языке.
Настоящий стандарт устанавливает требования к материалам, проектированию, изготовлению, сооружению и испытаниям вертикальных, цилиндрических, наземных сварных стальных резервуаров с закрытым и открытым верхом различных габаритов и различной...
American Petroleum Institute (API) Twentieth Edition, November 2005. 82p. This standard covers the gas and arc welding of butt, fillet, and socket welds in carbon and low-alloy steel piping used in the compression, pumping, and transmission of crude petroleum, petroleum products, fuel gases, carbon dioxide, nitrogen and, where applicable, covers welding on distribution systems.
American Petroleum Institute (API) Second Edition, December 2010. 96p. This standard contains practices for isolating potential flow zones, an integral element in maintaining well integrity. The focus of this standard is the prevention of flow through or past barriers that are installed during well construction
American Petroleum Institute (API) Second Edition, Reaffirmed March 2007. 76p. This recommended practice (RP) is intended to provide accurate information that can serve as a guide for selection, installation, testing, and operation of diverter equipment systems on land and marine drilling rigs (barge, platform, bottomsupported, and floating).
American Petroleum Institute (API) Sixth Edition, March 2004. Effective Date: September 2004. 72p. This specification details the requirements for design, construction, and testing of offshore pedestal mounted cranes.
American Petroleum Institute (API) Temth Edition, November 1998. Addendum 3, September 2003. 280p. This standard covers material, design, fabrication, erection, and testing requirements for vertical, cylindrical, aboveground, closed- and open-top, welded steel storage tanks in various sizes and capacities for internal pressures approximating atmospheric pressure (internal...
260 p.
Downstream Segment
American Petroleum InstituteThis recommended practice (RP) is intended to provide recommended procedures, practices, and checklists for the installation and precommissioning of new, existing, and reapplied machinery and to assist with the installation design of such machinery for petroleum, chemical, and gas industry services facilities. In general,...
American Petroleum Institute (API) Eleventh Edition, June 2007. 394p. This Standard establishes minimum requirements for material, design, fabrication, erection, and testing for vertical, cylindrical, aboveground, closed- and open-top, welded carbon or stainless steel storage tanks in various sizes and capacities for internal pressures approximating atmospheric pressure (internal...
American Petroleum Institute (API) Third Edition, January 2008. 56p. This specification states requirements and gives recommendations for suitable steel structures for drilling and well-servicing operations in the petroleum industry, provides a uniform method of rating the structures, and provides two PSLs.
American Petroleum Institute (API) Third Edition, August 1999, Reaffirmed March 2007. 50p. These recommendations apply to rotary drilling rigs, well servicing rigs, and special services as they relate to operations on location.
American Petroleum Institute (API) Second Edition, November 2007. 72p. This publication is intended to assist Operators, Contractors, and Subcontractors (Third Parties) in the implementation of a Contractor safety program and improve the overall safety performance while preserving the independent contractor relationship.
American Petroleum Institute (API) First Edition, April 1996. 160p. These recommended practices are intended to provide recommended procedures, practices, and checklists for the installation and precommissioning of new and reapplied machinery for petroleum, chemical, and gas industry services facilities
American Petroleum Institute (API) Third Edition, May 2001, Reaffirmed March 2007. 42p. Recommendations set forth in this publication apply to oil and gas well drilling and servicing operations involving hydrogen sulfide. These operations include well drilling, completion, servicing, workover, downhole maintenance, and plug and abandonment procedures conducted with hydrogen...
American Petroleum Institute (API) Fourth Edition, June 1995. 74p. This standard covers the minimum requirements for special-purpose, enclosed, precision single- and double-helical one- and two-stage speed increasers and reducers of parallel-shaft design for refinery services.
American Petroleum Institute (API) Second Edition, July 1997. 90p. This standard covers the minimum requirements for general-purpose, enclosed single and multistage gear units incorporating parallel shaft helical and right angle spiral bevel gears for the petroleum, chemical, and gas industries
American Petroleum Institute (API) Third Edition, September 1996. 87p. This standard establishes the minimum requirements for constant-speed, packaged, integrally geared centrifugal air compressors, including their accessories.
American Petroleum Institute (API) Second Edition, November 2010. 114p. This Recommended Practice addresses the special needs of valves and their accessories in control and safety instrumented system (SIS) applications for refinery services. The knowledge and experience of the industry has been captured to provide proven solutions to well-known problems
American Petroleum Institute (API) Second Edition, February 1998. 236p. Core analysis, like other technical areas, is continually evolving so that both methodology and costs are changing. The recommended practices provided here represent a snap shot in time of the consensus advice of a large international committee.
American Petroleum Institute (API) Seventh Edition, October 1989, Reaffirmed 1999. 84p. Covers minimum requirements for the design, fabrication, and plant testing of oil and gas separators and oil-gas-water separators that are used in the production of oil and gas, and are located at some point on the producing flow line between the wellhead and pipeline.
American Petroleum Institute (API) Second Edition, February 2003. 84p. This recommended practice covers the inspection practices for fired boilers and process heaters (furnaces) used in petroleum refineries and petrochemical plants.
American Petroleum Institute (API) First Edition, November 1997. 141p. The purpose of this recommended practice is to provides guidelines for classifying locations Class I, Zone 0, Zone 1, and Zone 2 locations at petroleum facilities for the selection and installation of electrical equipment.
American Petroleum Instiltute (API) Second Edition, November 1997. 119p. The purpose of this recommended practice is to provides guidelines for classifying locations Class I, Division 1 and Class 1 Division 2 at petroleum facilities for the selection and installation of electrical equipment Basic definitions given in the 1996 edition of NFPA 70, the National Electrical Code (NEC),...
American Petroleum Institute (API) Second Edition, October 1997. 12p. This recommended practice provides guidelines and procedures covering electric submersible pump performance testing intended to establish product consistency
American Petroleum Institute (API) Third Edition, December 2003. 112p. This standard is under the jurisdiction of API Subcommittee 13, Drilling and Completion Fluids. This API standard is a modified aboption of the English version of ISO 10414-1:2001.
American Petroleum Institute (API) Second Edition, March 2002. Effective Data, January 2005. 110p. These specifications establish design standards for systems, that are used to control blowout preventers (BOPs) and associated valves that control well pressure during drilling operations.
American Petroleum Institute (API) First Edition, April 2002. 76p. This document provides guidelines and recommended practice for the satisfactory design of offshore structures against fire and blast loading.
American Petroleum Institute (API) Second Edition, November 2002. 36p. This publication focuses on the design, implementation, testing and operation of CPM systems that use an algorithmic approach to detect hydraulic anomalies in pipeline operating parameters.
American Petroleum Instltute (API) First Edition, October 2001, Reaffirmed, March 2007. 36p. The purpose of this document is to recommend practices and procedures for promotion and maintenance of safe working conditions for personnel engaged in onshore oil and gas production, including special services.
American Petroleum Instltute (API) First Edition, September 2006. 127p. This document recommends minimum requirements and guidelines for the design and installation of electrical systems on fixed and floating petroleum facilities located offshore when hazardous locations are classified as Zone 0, Zone 1, or Zone 2.
American Petroleum Instltute (API) Fourth Edition, June 1999. 104p. This document recommends minimum requirements and guidelines for the design and installation of electrical systems on fixed and floating petroleum facilities located offshore
American Petroleum Instltute (API) Second Edition, May 2006. 106p. The purpose of these recommended practices is to provide information that can serve as a voluntary industry guide for safe well control operations. This publication is designed to serve as a direct field aid in well control and as a technical source for teaching well control principles.
American Petroleum Instltute (API) Second Edition, November 2001. 246p. Process monitors that measure and transmit information about chemical composition, physical properties, or chemical properties are known as process analyzer systems. Many of these systems were first developed for laboratory analysis. Today they are primarily used as continuous on-line analyzers.
American Petroleum Instltute (API) Fifth Edition, August 2003. 42p. This recommended practice covers methods of installation for pressure-relief devices for equipment that has a maximum allowable working pressure (MAWP) of 15 psig (1.03 bar g or 103 kPA) or greater
American Petroleum Instltute (API) Seventh Edition, January 2000. 100p. This recommended practice applies to the sizing and selection of pressure relief devices used in refineries and related industries for equipment that has a maximum allowable working pressure of 15 psig [103 kPag] or greater.
American Petroleum Instltute (API) Third Edition, May 2004. 52p. This recommended practice is intended to assist in development of a management program designed to promote safety and environmental protection during the performance of offshore oil and gas and sulphur operations.
American Petroleum Instltute (API) Third Edition, December 1993. 39p. This RP presents recommendations for minimizing the likelihood of having an accidental fire, and for designing, inspecting, and maintaining fire control systems. It emphasizes the need to train personnel in fire fighting, to conduct routine drills, and to establish methods and procedures for safe evacuation.
American Petroleum Instltute (API) Twenty-First Edition, December 2000, Errata and Supplement 1, December 2002. — 242 p. This publication serves as a guide for those who are concerned with the design and construction of new platforms and for the relocation of existing platforms used for the drilling, development, and storage of hydrocarbons in offshore areas. API publications...
American Petroleum Instltute (API) Ninth Edition, June 2006. 20p. This inspection code covers the in-service inspection, repair, alteration, and rerating activities for pressure vessels and the pressure-relieving devices protecting these vessels.
American Petroleum Instltute (API) Fifth Edition, January 2007. 202p. This International Standard is applicable to pressure-relieving and vapour-depressuring systems. Although intended for use primarily in oil refineries, it is also applicable to petrochemical facilities, gas plants, liquefied natural gas (LNG) facilities and oil and gas production facilities.
American Petroleum Instltute (API) Fourth Edition, April 1999. 240p. This international standard covers the minimum requirements for lubrication systems, oil-type shaft-sealing systems, dry gas face-type shaft-sealing systems, and controloil systems for general or special purpose applications
American Petroleum Instltute (API) Second Edition, September 2008. 654p. This publication provides quantitative procedures to establish an inspection program using risk-based methods for pressurized fixed equipment, including pressure vessel, piping, tankage, pressure relief devices, and heat exchanger tube bundles. This document is to be used in conjunction with API 580, which...
American Petroleum Institute (API) Forty-third Edition, March 2004, Effective Date: October 2004. 171p. The purpose of this specification is to provide standards for pipe suitable for use in conveying gas, water, and oil in both the oil and natural gas industries.
American Petroleum Instltute (API) Third Edition, January 1982. 18p. This standard covers the normal and emergency venting requirements for aboveground liquid petroleum storage tanks and aboveground and belowground refrigerated storage tanks designed for operation at pressures form 1/2 ounce per square inch vacuum through 15 pounds inch gage.
American Petroleum Instltute (API) Fourth Edition, April 2009. 166p. This standard covers steel storage tanks built to API 650 and its predecessor API 12C. It provides minimum requirements for maintaining the integrity of such tanks after they have been placed in service and addresses inspection, repair, alteration, relocation, and reconstruction.
American Petroleum Instltute (API) Eighth Edition, May 1995. 34p. This standard covers the design, construction, and location of liqueЮed petroleum gas (LPG) installations at marine and pipeline terminals, natural gas processing plants, reЮneries, petrochemical plants, or tank farms.
American Petroleum Instltute (API) Fifth Edition, June 1995. 23p. This standard is a purchase speciЮcation for Яanged steel pressure relief valves. Basic requirements are given for direct spring-loaded pressure relief valves and pilot-operated pressure relief valves.
American Petroleum Instltute (API) First Edition, May 1991. 68p. The procedures for installation of the instruments covered in this recommended practice are based on experience with and evaluation of many installations.
American Petroleum Instltute (API) Fifth Edition, October. 1991. Reaffirmed June 2000. 62p. This document recommends minimum requirements and guidelines for the design and installation of new piping systems on production platforms located offshore
American Petroleum Institute (API) First Edition, March 2001. 99p. This Recommended Practice (RP) provides guidelines for design, fabrication, installation, inspection and operation of Floating Production Systems (FPSs).
American Petroleum Institute (API) Forty-second Edition, July 2000. 168p. The purpose of this specification is to provide standards for pipe suitable for use in conveying gas, water, and oil in both the oil and natural gas industries.
American Petroleum Institute (API) Fifth Edition, June 2003. 54p. This Recommended Practice is intended to serve as a guide to crane owners and operators in developing operating and maintenance practices and procedures for use in the safe operation of pedestal-mounted revolving cranes on fixed or oating offshore platforms, jackup drilling rigs, semisubmersible drilling rigs and...
American Petroleum Institute (API) Fifth Edition, January 2002. 19p. This specification covers the fabrication of structural steel pipe formed from plate steel with longitudinal and circumferential butt-welded seams, typically in sizes 14 in. outside diameter (OD) and larger (40 in. and larger for LWDS) with wall thickness 3/8 in. and greater (up to a nominal 40 ft in length)...
American Petroleum Institute (API) First Edition, January 1998. 49p. Recommendations set forth in this publication apply to oil and gas well servicing and workover operations involving hydrogen sulfide.
American Petroleum Institute (API) Fifth Edition, June 2001. 30p. The following definitions are applicable to underground tank lining and inspection as described in this standard.
American Petroleum Institute (API) Sixth Edition, August 2001. 58p. This standard is applicable to cleaning stationaru atmospheric and lov-pressure (up to and including 15 psig) aboveground petroleum storage tanks used in all sectors of the petroleum and petrochemical industry, including crude oil and gas production, refineries, petrochemical plants, bulk plants and terminals.
The purpose of this recommended practice is to provide the guidelines for a material and quality assurance system to verify that the nominal composition of alloy components within the pressure envelope of a piping system is consistent with the selected or specified construction materials to minimize the potential for catastrophic release of toxic or hazardous liquids or vapors.
American Petroleum Institute (API) Temth Edition, November 1998. Addendum 2, November 2001. 240p. This standard covers material, design, fabrication, erection, and testing requirements for vertical, cylindrical, aboveground, closed- and open-top, welded steel storage tanks in various sizes and capacities for internal pressures approximating atmospheric pressure (internal pressures...
American Petroleum Institute (API) Temth Edition, February 2002. 196p. This standard is based on the accumulated knowledge and experience of purchasers and manufacturers of welded, low-pressure oil storage tanks of various sizes and capacities for internal pressures not more than 15 pounds per square inch gauge. The object of this publication is to provide a purchase specification...
American Petroleum Institute (API) Fourth Edition, September 1995. 23p. This publication covers the safety aspects to be considered when hot tapping, or when welding without hot tapping on in-service piping or equipment. It is not a substitute for job planning. A detailed, written procedure for hot tapping and welding should be prepared or reviewed before starting each job to...
American Petroleum Institute (API) Third Edition, January 2007. 46p. The purpose of this recommended practice is to present procedures and practices for achieving effective corrosion control on aboveground storage tank bottoms through the use of cathodic protection. It contains provisions for the application of cathodic protection to existing and new storage tanks. Corrosion...
American Petroleum Institute (API). First Edition. October 2004. 114p. This recommended practice (RP) provides guidance to the API authorized inspector on welding inspection as encountered with fabrication and repair of refinery and chemical plant equipment and piping. Common welding processes, welding procedures, welder qualifications, metallurgical effects from welding, and...
API 551 (1993)_Process Measurement Instrumentation.pdf ( 4206 KB)
API 552 (1994)_Transmission Systems.pdf (3162 KB)
API 553 (1998)_Refinery Control Valves.pdf (413 KB)
API 554 (1995)_Process Instrumentation and Control.pdf (5545 KB)
API 555 (2001)_Process Analyzers.pdf (3633 KB)
API 556 (1997)_Instrumentation and Control Systems.pdf (2423 KB)
API 557 (2000)_Guide To Advanced...
63 стр.
American Petroleum Institute, First Edition, Januaru, 1993
This specification was formulated to provide for safe and functionally interchangeable surface and subsea choke and kill systems equipment utilized for drilling oil and gas wells. Other parts of the Choke and Kill System not specifically addressed in this document shall be in accordance with the applicable...
67 стр.
American Petroleum Institute, Second Edition, December, 1997
This specification is formulated to provide for the availability of safe and functionally interchangeable drill through equipment utilized for drilling for oil and gas.
Technical content provides requirements for performance, design, materials, tests and inspection, welding, marking, handling, storing, and...
274 стр.
American Petroleum Institute, Third Edition, July 2010
This recommended practice is a guide to the designer in organizing an efficient approach to the design of a tension leg platform (TLP). Emphasis is placed on participation of all engineering disciplines during each stage of planning, development, design, construction, installation, and inspection.
288 стр.
American Petroleum Institute, Errata And Supplement 3, October 2007
This publication serves as a guide for those who are concerned with the design and construction of new platforms and for the relocation of existing platforms used for the drilling, development, and storage of hydrocarbons in offshore areas. In addition, guidelines are provided for the assessment of...
122 стр.
American Petroleum Institute, First Edition, February 2010
This document provides recommended practices for the design, operation, optimization, and troubleshooting of dual gas-lift wells. Compared to single completions, dual completions have a higher initial cost, have more operating problems, are more difficult and expensive to work over, and often produce less...
24 стр.
American Petroleum Institute, First Edition, September 2008
This document addresses four pipeline safety elements for hazardous liquid and natural gas pipelines in both the transportation and distribution sectors:
— pipeline control room personnel roles, authorities and responsibilities;
— guidelines for shift turnover;
— pipeline control room fatigue management; and...
30 стр.
American Petroleum Institute, Fifth Edition, June 2007
This Recommended Practice (RP) provides guidelines for pressure testing steel pipelines for the transportation of gas, petroleum gas, hazardous liquids, highly volatile liquids or carbon dioxide. The RP provides guidance so that:
a. Pipeline operators can select a pressure test suitable for the conditions under...
70 стр.
Downstream Segment
American Petroleum Institute, Ninth Edition , June 2006
General Application
Coverage
This inspection code covers the in-service inspection, repair, alteration, and rerating activities for pressure vessels and the pressure- relieving devices protecting these vessels. This inspection code applies to all refining and chemical process vessels that have...
374 стр.
American Petroleum Institute, The American Society of Mechanical Engineers, AUGUST 11, 2009
Fitness-For-Service (FFS) assessments in API 579-1/ASME FFS-1 Fitness-For-Service are engineering evaluations that are performed to demonstrate the structural integrity of an in-service component that may contain a flaw or damage or that may be operating under specific conditions...
1128 стр.
American Petroleum Institute, The American Society of Mechanical Engineers, JUNE 5, 2007, Second Edition
The methods and procedures in this Standard are intended to supplement and augment the requirements in API 510, API 570, API 653, and other post construction codes that reference FFS evaluations such as NB-23.
The assessment procedures in this Standard can be used...
150 стр. c Приложениями
Annex A (informative) Exchangers
Annex B (informative) Towers
Annex C (informative) Sample Record Forms
THIRD EDITION, NOVEMBER 2009
This recommended practice (RP) covers the inspection of pressure vessels. It includes a description of the various types of pressure vessels (including pressure vessels with a design pressure below 15 psig) and the...
220 стр.
ELEVENTH EDITION, SEPTEMBER 2010
ERRATA, JULY 2011
ISO 13709:2009 (Identical), Centrifugal pumps for petroleum, petrochemical and natural gas industries
This International Standard specifies requirements for centrifugal pumps, including pumps running in reverse as hydraulic power recovery turbines, for use in petroleum, petrochemical and gas industry process services....
148 стр.
EIGHTH EDITION, DECEMBER 2008
This standard applies to the sizing and selection of pressure relief devices used in refineries and related industries for equipment that has a maximum allowable working pressure of 15 psig (103 kPag) or greater. The pressure relief devices covered in this standard are intended to protect unfired pressure vessels and related equipment...
63 стр.
THIRD EDITION, NOVEMBER 2009
This recommended practice (RP) covers the inspection of pressure vessels. It includes a description of the various types of pressure vessels (including pressure vessels with a design pressure below 15 psig) and the standards for their construction and maintenance. This RP also includes reasons for inspection, causes of deterioration,...
44 стр.
FOURTH EDITION, APRIL 2009
ADDENDUM 1, AUGUST 2010
This standard covers steel storage tanks built to API 650 and its predecessor API 12C. It provides minimum requirements for maintaining the integrity of such tanks after they have been placed in service and addresses inspection, repair, alteration, relocation, and reconstruction.
The scope is limited to the tank...
78 стр.
THIRD EDITION, NOVEMBER 2009
The intent of this code is to specify the in-service inspection and condition-monitoring program that is needed to determine the integrity of piping. That program should provide reasonably accurate and timely assessments to determine if any changes in the condition of piping could possibly compromise continued safe operation. It is also the...
API Standard 1104 Nineteenth edition, September 1999, Errata 1, October 31, 2001, 86p. This standard covers the gas and arc welding of butt, .fillet, and socket welds in carbon and low-alloy steel piping used in the compression, pumping, and transmission of crude petroleum, petroleum products, fuel gases, carbon dioxide, and nitrogen and, where applicable, covers welding on...
API STANDARD 600 TENTH EDITION, FEBRUARY 1997, 28p. This standard covers steel gate valves with flanged or butt-welding ends in sizes NPS 1 througn NPS
24. These sizes correspond to nominal pipe sizes in ASME B36.10M.
ANSI/API STANDARD 560 FOURTH EDITION, AUGUST 2007,ISO 13705:2006 (Identical), 276p, This International Standard specifies requirements and gives recommendations for the design, materials, fabrication, inspection, testing, preparation for shipment, and erection of fired heaters, air preheaters, fans and burners for general refinery service.
5th edition. — API, 2007. This standard is based on the accumulated knowledge and experience of manufacturers and users of reciprocating compressors. The objective of this publication is to provide a purchase specification to facilitate the procurement and manufacture of reciprocating compressors for use in petroleum, chemical, and gas industry services. The primary purpose of...
4th edition. — API, 1995. — 167 p. This standard covers the minimum requirements for reciprocating compressors and their drivers used in petroleum, chemical, and gas industry services for handling process air or gas with either lubricated or nonlubricated cylinders. Compressors covered by this standard are of mod- erate-to-low speed and in critical services. Also covered are...
220 стр.
ANSI/API STANDARD 610
ELEVENTH EDITION, SEPTEMBER 2010
ERRATA, JULY 2011
ISO 13709:2009 (Identical), Centrifugal pumps for petroleum, petrochemical and natural gas industries
This International Standard specifies requirements for centrifugal pumps, including pumps running in reverse as hydraulic power recovery turbines, for use in petroleum, petrochemical and gas...
46 стр.
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that...
20 стр.
API SPECIFICATION Q1
SIXTH EDITION, MARCH 1, 1999
EFFECTIVE DATE: SEPTEMBER 1, 1999
API Specification Ql provides requirements for a quality system that may be applied on an international basis to facilitate the consistent and reliable manufacture of products to specifications prepared for the oil and gas industry. Part One of this Standard is aligned with...
180 стр.
API STANDARD 616
FIFTH EDITION, JANUARY 2011
This standard covers the minimum requirements for open, simple, and regenerative-cycle combustion gas turbine units for services of mechanical drive, generator drive, or process gas generation. All auxiliary equipment required for operating, starting, controlling, and protecting gas turbine units are either discussed...
100 стр.
API STANDARD 616
FOURTH EDITION, AUGUST 1998
This standard covers the minimum requirements for open, simple, and regenerative-cycle combustion gas turbine units for services of mechanical drive, generator drive, or process gas generation. All auxiliary equipment required for operating, starting, and controlling gas turbine units and for turbine protection is either...
48 стр SDO: API: American Petroleum Institute This International Standard is based on API RP 5A3, first edition, June 1996. This International Standard specifies requirements and gives recommendations for the manufacture, testing and selection of thread compounds for use on casing, tubing and line pipe based on the current industry consensus of good engineering practice. It is...
415 стр.
EFFECTIVE DATE: FEBRUARY 1, 2005
ANSI/API 6A/ISO 10423-2003
This International Standard is based on API Spec 6A, seventeenth edition, February 1996, its errata and
supplement, and API Spec 6AV1, first edition, February 1996. The contents of API Spec 14D (upon which ISO 10433 was based) and API Recommended Practice 14H (upon which ISO 10419 was based) have been...
234 стр.
Current status: Active
Short description: Covers the minimum requirements for centrifugal compressors used in petroleum, chemical, and gas industry services that handle air or gas, including process gear mounted. Does not apply to fans or blowers that develop less than 34 kPa (5 pounds per square inch) pressure rise above atmospheric pressure; these are covered by API...
American Petroleum Institute / 01-Sep-2010 / 220 pages.
Edition: 11th.
Eleventh Edition (ISO 13709:2009 Identical Adoption).
Scope.
This International Standard specifies requirements for centrifugal pumps, including pumps running in reverse as hydraulic power recovery turbines, for use in petroleum, petrochemical and gas industry process services.
This International Standard...
API Spec 5L-04 Specification for Line Pipe API Spec 5CT Specification for Casing and Tubing API 6A / ISO 10423 Specification 6A API Spec 6D:2002 Арматура трубопроводная промышленная. Спецификация API API Spec 6FA:1999 Спецификация на испытание арматуры на пожаростойкость API Spec 6FD:1995 Спецификация на испытание обратной арматуры на пожаростойкость API RP 521:1997 Guide for...
Комментарии