EN ISO

ISO 22301 Societal security – Business continuity management systems – Requirements is a management system standard that specifies requirements to plan, establish, implement, operate, monitor, review, maintain and continually improve a documented management system to protect against, reduce the likelihood of occurrence, prepare for, respond to, and recover from disruptive...

ISO 17491-3:2008 specifies a test method for determining the resistance of protective clothing against penetration by a jet of liquid. ISO 17491-3:2008 is applicable to clothing with liquid-tight connections between different parts of the clothing and, if applicable, between the clothing and other items of personal protective equipment worn with it. ISO 17491-3:2008 does not...

ISO 17491-4:2008 specifies methods for determining the resistance of chemical protective clothing to penetration by sprays of liquid chemicals at two different levels of intensity: Method A: low-level spray test. This is applicable to clothing that covers the full body surface and which is intended to be worn when there is a potential risk of exposure to small quantities of...

BS ISO 17493:2016 describes a test method for evaluating the heat resistance of protective clothing materials or items and equipment when exposed in a hot air circulating oven. The method is intended to evaluate physical changes in a material at a given exposure temperature. Materials are evaluated for defined visible changes including the measurement of shrinkage. Different...

ISO/IEC 18033-5:2015 specifies identity-based encryption mechanisms. For each mechanism the functional interface, the precise operation of the mechanism, and the ciphertext format are specified. However, conforming systems may use alternative formats for storing and transmitting ciphertexts.

Международная организация по стандартизации. — 2010. — 22 с. Данный международный стандарт устанавливает уровни приемки 2 и 3 для сварных соединений, выполненных из ферритных сталей с полным проплавлением, которые соответствуют уровням качества "В" и "С" ISO 5817.

The International Organization for Standardization (ISO). The text of ISO 11681-2:2006 has been approved by CEN as EN ISO 11681-2:2006 without any modifications. This document supersedes EN ISO 11681-2:1998. 29p. This part of ISO 11681 specifies safety requirements and their verification for the design and construction of portable combustion-engine, hand-held chain-saws for...

The International Organization for Standardization (ISO). First edition, 2003-11-01. 43р. This standard defines technical principles to help designers in achieving safety in the design of machinery. ISO 12100-2 is intended to be used together with ISO 12100-1 when considering the solution to a specific problem. The two parts of ISO 12100 can be used independently of other...

The International Organization for Standardization (ISO). The text of ISO 13919-2:2001 has been approved by CEN on 13 April 2000, and amendment A1 was approved by CEN on 20 November 2003. 14p. This standard provides guidance on levels of imperfections in electron and laser beam welded joints in aluminium and its alloys.

This European Standard specifies general tolerances for linear and angular dimensions and for shape and position of welded structures in four tolerance classes, these being based on customary workshop accuracy. The main criterion for the selection of a particular tolerance class should be the functional requirements which are to be met.

Часть польской версии стандарта EN ISO. Перевод польского комитета стандартизации, май 2011, 8 стр. Содержит общие требования к площадкам для обслуживания оборудования и проходам у оборудования.

The International Organization for Standardization (ISO). 2003. This document supersedes EN 288-1:1992. 18p. This Standard is part of a series of standards. Annex A gives details of this series of standard, annex B gives a flowchart for the use of these standards and Annex C gives a flow diagram for the development and qualification of a WPS. This standard defines general rules...

The International Organization for Standardization (ISO). 2003. Supersedes EN 288-5:1994. 7p. This standard is a part of a series of standards, details of this series are given in EN ISO 15607:2003. This standard gives the necessary information to explain the requirements referenced in EN lSO 15607:2003 about the qualification of welding procedures based on tested consumables....

This European Standard is a part of a series of standards, details of this series are given in EN ISO 15607:2003, annex A. This standard specifies how a preliminary welding procedure specification is qualified based on pre-production welding tests. This standard is applicable to arc welding, gas welding, beam welding, resistance welding, stud welding and friction welding of...

This part of ISO 15614 specifies how a preliminary welding procedure specification is qualified by welding procedure tests. It applies to the arc and gas welding of copper and copper alloys in all product forms. This part of ISO 15614 defines the conditions for the execution of welding procedure tests and the range of qualification for welding procedures for all practical welding...

CEN, 2016. — 15 p. This document specifies techniques for detection of surface imperfections in welds in ferromagnetic materials, including the heat affected zones, by means of magnetic particle testing. The techniques are suitable for most welding processes and joint configurations. Variations in the basic techniques that will provide a higher or lower test sensitivity are...

This document has been prepared by Technical Committee CEN/TC162 "Protective clothing including hand and arm protection and lifejackets", the secretariat of which is held by DIN, in collaboration with Technical Committee ISO/TC 94 "Personal safety - Protective clothing and equipment". This European Standard was approved by CEN on 24 December 2004. This document supersedes EN...

This International Standard specifies the data fields used in the title blocks and headers of technical product documents. Its purpose is to facilitate the exchange of documents and ensure compatibility by defining field names, their contents and their length (number of characters). It covers manual as well as computer-based design work, and is applicable to all kinds of...

Действие 2003 Язык: русский Страниц 11 В настоящем Международном стандарте описывается метод определения содержания серы в нефтепродуктах, таких как бензиновые растворители, неэтилированный моторный бензин, средние дистилляты, мазутные виды топлива, базовое смазочное масло и основные его компоненты. Этот метод применяется к продуктам, содержание серы в которых находится в...