BSI, 2011. — 7 p. — ISBN 978 0 580 72092 5. The text of ISO 9016:2001 has been prepared by Technical Committee ISO/TC 44 “Welding and allied processes” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 9016:2011 by Technical Committee CEN/TC 121 “Welding” the secretariat of which is held by DIN. This European Standard shall be given...
British Standatd Institution, 1997. — 18 p. This part of ISO 11843 specifies terms and definitions relating to the detection of a difference between an actual state of a system and its basic state.
British Standatd Institution, 2000. — 34 p. This part of ISO 11843 specifies basic methods to: - design experiments for the estimation of the critical value of the net state variable, the critical value of the response variable and the minimum detectable value of the net state variable, - estimate these characteristics from experimental data for the cases in which the...
British Standatd Institution, 2003. — 18 p. This part of ISO 11843 gives a method of estimating the critical value of the response variable from the mean and standard deviation of repeated measurements of the reference state in certain situations (see 5.1) in which the value of the net state variable is zero, for all reasonable and foreseeable purposes. Hence, it can be decided...
British Standatd Institution, 2003. — 16 p. This part of ISO 11843 deals with the assessment of the capability of detection of a measurement method without the assumptions in ISO 11843-2 of a linear calibration curve and certain relationships between the residual standard deviation and the value of the net state variable
British Standatd Institution, 2008. — 26 p. This part of ISO 11843 is concerned with calibration functions that are either linear or non-linear. It specifies basic methods to ⎯ construct a precision profile for the response variable, namely a description of the standard deviation (SD) or coefficient of variation (CV) of the response variable as a function of the net state...
This part of ISO 12151 specifies the general and dimensional requirements for the design and performance of hose fittings with O-ring face seal ends in accordance with ISO 8434-3, made of carbon steel, for nominal hose inside diameters of 6,3 mm to 38 mm inclusive, in accordance with ISO 4397.
NOTE 1 Materials other than carbon steel may be supplied as agreed between the...
This part of ISO 12151 specifies the general and dimensional requirements for the design and performance of
hose fittings with 24° cone connector ends with O-rings, in accordance with ISO 8434-1 and ISO 8434-4.
These hose fittings are made of carbon steel and are intended for use with hoses with nominal inside
diameters from 5 mm through 38 mm (inclusive).
NOTE 1 Materials...
This part of ISO 12151 specifies the general and dimensional requirements for the design and performance of flange hose fittings, made of carbon steel, for nominal hose inside diameters of 12,5 mm to 51 mm inclusive, in accordance with ISO 4397, for use with ports and clamps in accordance with ISO 6162.
NOTE 1 Materials other than carbon steel may be supplied as agreed between...
This part of ISO 12151 specifies the general and dimensional requirements for the design and performance of
37° flared hose fittings in accordance with ISO 8434-2, made of carbon steel, for nominal hose sizes of
6,3 mm through 51 mm inclusive in accordance with ISO 4397.
NOTE 1 Other materials can be supplied as agreed between the manufacturer and user.
NOTE 2 See ISO 4038 and...
BSI, 2002. — 36 p. This International Standard provides guidelines to enable translators and translation support staff to record, maintain and quickly and easily retrieve terminological information in connection with translation work. The quality of a translation can be measured partly in terms of linguistic elements, such as style and grammar, and partly in terms of the...
2001. BSI –Институт Британских Стандартов. —147 стр. Этот международный стандарт основан на API стандарте 530[30], четвертое издание, Октябрь 1996 г. Данный международный стандарт определяет требования и дает рекомендации по процедурам и критериям оформления, используемых для вычисления необходимой толщины стенки новых труб для нагревателей нефтеперерабатывающего завода. Эти...
This International Standard specifies requirements for a security printing management system for security printers. This International Standard specifies a minimum set of security printing management system requirements. Organizations ensure that customer security requirements are met as appropriate provided these do not conflict with the requirements of this International...
The International Organization for Standardization (ISO). Second edition 2006-02- 15. This second edition cancels and replaces the first edition (ISO 14520-8:2000), which has been technically revised. This British Standard reproduces verbatim ISO 14520-8:2006 and implements it as the UK national standard. 4 p. This part of ISO 14520 gives specific requirements for gaseous...
BSI, 2004. — 34 p. This International Standard specifies technical requirements for the enhanced functionality of ship's bridge layout and design, with the key navigational functions centralized and integrated, for the purpose of securing safe and efficient operation of the ship, berth–to–berth, regardless of the watchkeeping arrangement in place at a particular time. The...
Geneva (Switzerland), ISO 2015, p. 56. . This part of ISO 15519 deals with representation of measurement, actuation, and control in process diagrams which in this context covers process flow diagrams (PFD), process and instrument diagrams (PID), process control diagrams (PCD), and typical diagrams (TYD). Foreword. 1 Scope. 2 Normative references. 3 Terms, definitions, and...
Standard Number BS ISO 16000-3:2001 Title Indoor air. Determination of formaldehyde and other carbonyl compounds. Active sampling method Status Revised, Withdrawn Publication Date 17 December 2001 Confirm Date 01 July 2006 Withdrawn Date 30 November 2011 Cross References Method TO-11A, EPA-625/R-96-010b, ASTM D5197-97, USEPA, Report No. 450/4-91/006, USEPA, Report No....
Standard Number BS ISO 16000-6:2011 Title Indoor air. Determination of volatile organic compounds in indoor and test chamber air by active sampling on Tenax TA sorbent, thermal desorption and gas chromatography using MS or MS-FID Status Under review, Current Publication Date 31 March 2012 Cross References ISO 16000-1, ISO 16017-1:2000, ISO 6141, ISO 6145, ISO 12219-1, ISO...
Standard Number BS ISO 16000-8:2007 Title Indoor air. Determination of local mean ages of air in buildings for characterizing ventilation conditions Status Confirmed, Current Publication Date 31 July 2007 Confirm Date 04 April 2016 Cross References ISO 12569, ISO/IEC Guide 98:1995, ISO 16000-1, ISO 16017-1, ISO 16017-2 International Relationships ISO 16000-8:2007 Draft...
This British Standard is the UK implementation of ISO 16792:2006. It supersedes DD 16792:2002 which is withdrawn. 28 September 2007 BSI, 0 p. Every effort was made during the preparation of this International Standard — adapted from ASME Y14.41:2003 — to apply existing requirements developed for two-dimensional (2-D) presentation equally to the output from three-dimensional...
This British Standard is the UK implementation of ISO 16900-1:2014. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2014. — 6 p. — ISBN: 978 0 580 54033 2. This part of ISO 16900 specifies the test methods for determining inward leakage of respiratory interfaces (RI) and total inward leakage of complete...
This British Standard is the UK implementation of ISO 16900-10:2015. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2015. — 0 p. — ISBN: 978 0 580 79510 7. This part of ISO 16900 specifies the methods for resistance to ignition, flame, radiant heat, and heat.
This British Standard is the UK implementation of ISO 16900-11:2013. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2013. — 2 p. — ISBN: 978 0 580 70760 5. This part of ISO 16900 specifies the laboratory test method for determining the field of vision for a respiratory protective device (RPD).
This British Standard is the UK implementation of ISO 16900-13:2015. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2015. — 4 p. — ISBN: 978 0 580 80494 6. This part of ISO 16900 specifies tests which are specific to RPDs using regenerated breathable gas, compressed breathable gas with class L respiratory...
This British Standard is the UK implementation of ISO 16900-14:2015. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 November 2015. — 8 p. — ISBN: 978 0 580 82430 2. This part of ISO 16900 specifies a laboratory test method for determining the sound level generated by the complete respiratory protective device (RPD)...
This British Standard is the UK implementation of ISO 16900-3:2012. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2013. — 2 p. — ISBN: 978 0 580 54034 9. This part of ISO 16900 specifies the test methods for particle filter penetration of separate or integral filters for respiratory protective devices.
This British Standard is the UK implementation of ISO 16900-4:2011. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2013. — 6 p. — ISBN: 978 0 580 76514 8. This part of ISO 16900 specifies the test method for determining the gas capacity of separate or integral gas filters and combined filters for respiratory...
This British Standard is the UK implementation of ISO 16900-8:2015. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2015. — 4 p. — ISBN: 978 0 580 78312 8. This part of ISO 16900 specifies the methods for measuring air flow rates delivered to the wearer by an assisted filtering RPD.
This British Standard is the UK implementation of ISO 16900-9:2015. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2015. — 2 p. — ISBN: 978 0 580 80713 8. This part of ISO 16900 specifies the test methods for determining the increased carbon dioxide content of the inhaled gas caused by wearing the RPD. Closed...
This British Standard is the UK implementation of ISO 16972:2010. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2014. — 6 p. — ISBN: 978 0 580 54109 4. This International Standard is applicable to respiratory protective devices. It defines commonly used terms and specifies units of measurement to achieve a...
The International Organization for Standardization (ISO). First edition. 2005-12- 01. This first edition of ISO 19901-7 cancels and replaces ISO/TR 13637:1997, of which it constitutes a technical revision. This British Standard reproduces verbatim ISO 19901-7:2005 and implements it as the UK national standard. 8 p. This part of ISO 19901 specifies methodologies for a) the...
The International Organization for Standardization (ISO). First edition, 2006-05-01. 4 p. This International Standard specifies minimum requirements for the material, design, construction and workmanship, manufacturing processes and tests at manufacture of refillable, transportable, welded aluminium-alloy gas cylinders of water capacities from 0,5 l up to and including 150 l,...
BSI, 2010. — 50 p. The International Standard gives guidance for ⎯ evaluation of measurement uncertainties using data obtained from studies conducted in accordance with ISO 5725-2:1994; ⎯ comparison of collaborative study results with measurement uncertainty (MU) obtained using formal principles of uncertainty propagation (see Clause 13). ISO 5725-3:1994 provides additional...
BSI, 2009. — 38 p. This International Standard identifies and describes a wide range of terminology products and services so that suppliers of these products and services and their clients can have a common understanding as well as shared expectations in their delivery. This International Standard outlines some of the generally-accepted terminology practices to be followed in...
Данный международный стандарт предоставляет методику количественного анализа с использованием рентгеноспектрального микроанализа.
This International Standard gives guidance on the quantitative analysis at specific points or areas of a
specimen using energy-dispersive spectrometry (EDS) fitted to a scanning electron microscope (SEM) or
electron probe microanalyser (EPMA); any...
BSI, 2012. — 170 p. This part of ISO 230 specifies methods for testing the accuracy of machine tools, operating either under no-load or under quasi-static conditions, by means of geometric and machining tests. The methods can also be applied to other types of industrial machines. This part of ISO 230 covers power-driven machines, which can be used for machining metal, wood,...
BSI, 2011. — 94 p. This International Standard provides dialysis practitioners with guidance on the preparation of dialysis fluid for haemodialysis and related therapies and substitution fluid for use in online therapies, such as haemodiafiltration and haemofiltration. As such, this International Standard functions as a recommended practice.
The International Organization for Standardization (ISO). Fourth edition. 2008-07-01. 6 p. This part of ISO 3601 specifies the inside diameters, cross-sections, tolerances and designation codes for O-rings used in fluid power systems for general industrial and aerospace applications. The dimensions and tolerances specified in this part of ISO 3601 are suitable for any...
Стандарт ИСО, который вышел 12 марта 2018 г. на замену OHSAS 18001:2007. Назначение системы менеджмента охраны здоровья и безопасности труда (ОЗБТ) состоит в том, чтобы обеспечить среду для управления рисками и возможностями в области ОЗБТ. Ожидаемыми результатами функционирования системы менеджмента ОЗБТ являются предотвращение травм и ущерба для здоровья сотрудников, а также...
The International Organization for Standardization (ISO). 1993, 7 pages. This International Standard specifies methods for inspection and repair of solid-section fork arms in use on all types of fork-lift trucks.
British Standatd Institution, 1994. — 26 p. The purpose is to outline the general principles to be understood when assessing accuracy (trueness and precision) of measurement methods and results, and in applications, and to establish practical estimations of the various measures by experiment. Is concerned exclusively with measurement methods which yield measurements on a...
British Standatd Institution, 1994. — 62 p. This part of ISO 5725 — amplifies the general principles to be observed in designing experiments for the numerical estimation of the precision of measurement methods by means of a collaborative interlaboratory experiment; — provides a detailed practical description of the basic method for routine use in estimating the precision of...
British Standatd Institution, 1994. — 38 p. This part of ISO 5725 specifies four intermediate precision measures due to changes in observation conditions (time, calibration, operator and equipment) within a laboratory. These intermediate measures can be established by an experiment within a specific laboratory or by an interlaboratory experiment. Furthermore, this part of ISO...
British Standatd Institution, 1994. — 32 p. This part of ISO 5725 provides basic methods for estimating the bias of a measurement method and the laboratory bias when a measurement method is applied.
British Standatd Institution, 1998. — 64 p. This part of ISO 5725 — provides detailed descriptions of alternatives to the basic method for determining the repeatability and reproducibility standard deviations of a standard measurement method, namely the split-level design and a design for heterogeneous materials; — describes the use of robust methods for analysing the results...
British Standatd Institution, 1994. — 58 p. The purpose of this part of ISO 5725 is to give some indications of the way in which accuracy data can be used in various practical situations by: a) giving a standard method of calculating the repeatability limit, the reproducibility limit and other limits to be used in examining the test results obtained by a standard measurement...
The International Organization for Standardization (ISO). Second edition, 2006-02- 15. This second edition cancels and replaces the first edition (ISO 6149-1:1993), which has been technically revised. 4 p. This part of ISO 6149 specifies dimensions for metric ports for use with the adjustable and non-adjustable stud ends detailed in ISO 6149-2 and ISO 6149-3. Ports in...
This part of ISO 6149 specifies dimensions, performance requirements and test procedures for metric
adjustable and non-adjustable heavy-duty (S series) stud ends and O-rings.
Stud ends in accordance with this part of ISO 6149 may be used at working pressures up to 63 MPa
(630 bar) for non-adjustable stud ends and 40 MPa (400 bar) for adjustable stud ends. The permissible...
The International Organization for Standardization (ISO). First edition, 2006-05-15. 0 p. This part of ISO 6149 specifies dimensions and performance requirements for external hex and internal hex port plugs for use with ISO 6149-1 ports. Port plugs in accordance with this part of ISO 6149 can be used at working pressures up to 63 MPa (630 bar1)). The permissible working...
The International Organization for Standardization (ISO). Second edition. 2009-09- 15. This second edition cancels and replaces the first edition (ISO 6469-1:2001), which has been technically revised. 8 p. This part of ISO 6469 specifies requirements for the on-board rechargeable energy storage systems (RESS) of electrically propelled road vehicles, including battery-electric...
The International Organization for Standardization (ISO). Third edition. 2007-05- 01. This third edition cancels and replaces the second edition (ISO 6534:1992), of which subclauses 5.2.2 and 5.3 have been technically revised. This British Standard was published by BSI. It is the UK implementation of ISO 6534:2007. 2 p. This International Standard specifies the mechanical...
BSI, 2008. — 50 p. This International Standard specifies the functional requirements for bridge configuration, bridge arrangement, bridge workstations and bridge environment. Guidelines have been drawn up for the methods and solutions to meet the functional requirements.
The International Organization for Standardization (ISO). First edition, 2005-11-01. 8 p. This part of ISO 857 defines terms used for metal soldering and brazing processes, as well as related terms.
Specification for face-to-face, centre-to-face, end-to-end and centre-to-end dimensions of flanged and butt-welding end steel valves for the petroleum, petrochemical and allied industries
First edition 2010-11-01
This International Standard provides guidance to all types of organizations, regardless of their size or location, on:
a) concepts, terms and definitions related to social responsibility;
b) the background, trends and characteristics of social responsibility;
c) principles and practices relating to social responsibility;
d) the core subjects and...
Standard Number DD ISO/TR 15969:2001 Title Surface chemical analysis. Depth profiling. Measurement of sputtered depth Status Current Publication Date 01 October 2001 Cross References ASTM E 673, ASTM E 1438, ASTM E 1127, ASTM F 576, ISO 14606 International Relationships ISO/TR 15969:2001 Descriptors Surface chemistry, Surface properties, Chemical analysis and testing, Depth,...
BSI, 2004. — 40 p. The Technical Specification gives guidance for - evaluation of measurement uncertainties using data obtained from studies conducted in accordance with ISO 5725-2:1994; - comparison of collaborative study results with measurement uncertainty (MU) obtained using formal principles of uncertainty propagation (see Clause 14).
BSI, 2000. — 16 p. This Guide is intended to help producers to prepare clear and concise certificates to accompany certified reference materials. Such certificates, while maintaining their essential character, should help to provide, in summary form, all the information needed by the user of the reference material.
BSI, 2000. — 32 p. This Guide discusses the uses of certified reference materials (CRMs) and their correct applications. Clause 2 of this Guide presents definitions (with indication of their sources) of terms used, and clause 4 sets out the statistical considerations on which the Guide is based. Clause 5 discusses the role of CRMs in measurement science and in realization of...
BSI, 2009. — 16 p. This Guide recommends terms and the meanings that should be assigned to them when used in connection with reference materials, with particular attention to terms that are used in reference material certificates and corresponding certification reports.
BSI, 2010. — 46 p. 1.1 This Guide specifies general requirements in accordance with which a reference material producer has to demonstrate that it operates, if it is to be recognized as competent to carry out the production of reference materials. 1.2 This Guide is intended for the use by reference material producers in the development and implementation of their management...
BSI, 2012. — 49 p. This Technical Report describes the measurement process where the characteristic(s) being measured is a continuous variable. Measurement processes where the characteristic(s) of interest is an attribute (i.e. pass/fail) are not treated in this document. This Technical Report provides examples of simple measurement systems and gives usable results as used in...
BSI, 2005. — 42 p. This Technical Report provides users with practical guidance to the use of ISO 5725-2:1994 and presents simplified step-by-step procedures for the design, implementation, and statistical analysis of inter-laboratory studies for assessing the variability of a standard measurement method and on the determination of repeatability and reproducibility of data...
BSI, 2005. — 34 p. This part of ISO 230 provides information on a possible estimation of measurement uncertainties for measurements according to ISO 230. The methods described here are aimed for practical use; therefore, standard uncertainties are mainly evaluated by type B evaluation (see Clause 4 and GUM). Other methods complying with GUM may be used.
BSI, 2012. — 46 p. This Technical Specification provides general guidance for all phases of a translation project. Its main purpose is to facilitate communication among the parties involved in a project. It is intended for use by all stakeholders of the translation project, including those who request translation services, those who provide the services and those who make use...
Комментарии